Subject: 3 rotor turbo compound in boat
From: rotaryeng
Date: 7/2/2013, 10:35 PM
To: AAA-rotaryeng


 You know, it will cost over a quarter of a million dollars to replace the
 diesels in my boat, and with that in mind I am watching  the TC rotary with
 genuine interest. My 12V71s are rated at 550HP each at 2200 RPM, but I
 never run them at that because of the fuel burn. I have even considered the
 cruise ship approach- 3 generators and use electric motors to turn the
 props. As the load increases, fire up another generator.

 I run the diesels at around 1200 RPM because the fuel burn is almost
 exponential after that-  at 1200 RPM x 2 engines the fuel burn is around 17
 gph (total) and my speed is around 11 knots. At 2000 RPM the speed goes to
 18 knots, and the fuel burn passes 65 gph (total). less than 1/3 mile par
 gallon, Obama would be shocked!

 I have a fuel burn chart from DD for these engines at various RPM and HP,
 when I get time to look through all these HDDs I will send it to you- but
 here is what is important-

 My props are 32" dia x 29 pitch, 4 blades put through a 2:1 gear box. Each
 12V71 weighs around 2.5 tons. Yep, 2.5 tons. And the Allison gear drives
 weigh 850 lbs each, in addition to the engine weight. Not to mention that
 these engines are loud, and are as big as the back of my truck. To get them
 out requires a big hole be cut in the side of the boat.

 I have been looking into the Detroit Diesel series 60 650 HP diesels as
 replacements. I would need to change the flywheel, bellhousing and add a
 heat exchanger to make it work, but thats easy. I can get a reman Series 60
 for just over 12K in a box, which isn't too bad considering over 110K for a
 "marine" engine. The other plus is a 1/3 decrease in fuel burn and 2.5 tons
 less weight.

 As far as the TC rotary, we would need a 6:1 gear box, but I would be
 interested in trying it out. Can you imagine the look on the other captains
 faces when I pass them in a boat that weighs 81,000 lbs with engines that
 are as big in diameter as their toilet?

 Thanks for the hard work Paul, we really appreciate it.

 KA


 Here is what it looks like currently.
 Next project is the exhaust plumbing.

 Paul Lamar



It looks like you are going to drive it through the big bolt on the crank?

The arrow would seem to indicate that the torque will have a tendency to
unscrew the bolt unless I am seeing it wrong. And based on the direction of
the arrow, isn't it turning backwards?

http://www.tractorsupply.com/en/store/overrunning-pto-coupler-1-1-8-in-x-6-female-spline?cm_vc=-10005

This is an overrun clutch that we use in tractor PTO drives. I doubt it
will hold up at 6K RPM, but I am sure there is one to handle the torque/
HP. We used them on 12 foot wide bush hogs for highway mowing behind 100+
HP tractors. If you could find something like this I think it would help
somewhat. It would let the engine rev up independently of the turbine
gearbox and when the gearbox catches up it would deliver power.

I would think that there wouldnt be a problem with the turbine pushing the
crank, it would be more of a problem with the sharp acceleration of the
crank trying to instantly deliver start the turbine spinning. It would also
help if the engine had oil pumping before the turbine started rotating too.

Kevin Alderman

No I machined a coupling. The arrow was drawn in error.
I am going to use two of these 1 inch shaft U-joints back to back.

Never the less it takes a very strong air driven impact wrench to
unscrew that infamous bolt :)


Your right about the turbine spin up but there is also
a fluid coupling in the TC gear box. It's starting torque
characteristics are unknown at this point.

Paul Lamar

-- 
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net.
You Tube http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.