Subject: Major mile stone on turbo compound
From: rotaryeng
Date: 7/10/2013, 11:49 AM
To: AAA-rotaryeng


The coupler is done.
This is a bit over kill for 50  HP  but when the rotary starts up it is
going to try to spin up the  turbine  through the fluid couplings.

Another point.
We may  need a more  powerful starter motor as the turbine will have to  be
spun to 3000 RPM  while the engine is cranking at 500  RPM.


This took a relatively  long time and one false start got  discarded.

Paul Lamar


Do  you have any photo's of the  whole kit and caboodle?  The way that
looks,  with my  engine
in the rear, half of it would be in my back seat.    Thanks.  Love the
progress  updates.
Exciting.

Chris


Not flight hardware. Dyno  test  only.

It is going to weigh close to 450  pounds.

Paul  Lamar



Paul --

Am I missing  something? According to the little arrows marked on the
turbine gearbox in  one of the photos, either the engine or the turbine
will be
running  backwards, and I don't think rotaries run backwards very well. I'm
certain  there's an explanation.

Fuller

I put those on by mistake before  I had the turbine part.

How's it going Don ? If you get up to Santa  Paula let me know
and you can tour the hangar and have drive in the  RX8.

I am thinking of getting an article in Pop Mechanics about the  TC.
Are you interested in writing it ?

Also the time to climb 600 HP  2 rotor turbo Harmon Rocket is out in
your neck of the woods at Corona  airport. I will let you know when Racing
Beat gets the engine mounted. I  would like some pictures.
That would make a great article too.

Paul  Lamar
-- 
Paul --

Lemme get this straight. You made a mistake? Paul, Paul, Paul -- must be
those advancing years taking their pesky toll.

As for getting up to Santa Paula that don't haps much often, but it would
be great to visit and see what you got going.

However, if you need a typewriter banger to knock out the TC piece we can
certainly talk about that. I have been a fan of turbocompounding for years.
One  of my amazingly brilliant ideas -- about which I may have told you and
about  which I am sure, if I did, you would have rolled your eyes -- was for
race cars.  It went like this: Use a couple of turbocharger exhaust turbine
sections, one  per side, and have them connected to reduction gearboxes (as
with the Detroit  Diesel TC unit) and have that power fed directly into the
output sides of the  rear-mounted gearbox, so the power gain goes directly
to the rear wheels. The  engine remains normally aspirated. It probably
wouldn't work so well for road  racing, where there is lots of engine and
vehicle-speed variation, but for, say,  Indianapolis or Pocono, where they're
pretty much flat out just about all the  time it could be beneficial, both from
power and fuel economy standpoints. The  reason the engine would remain
normally aspirated (this was obviously thought of  back in the days of different
engine choices based on stock blocks and  aspiration, etc) was that you
would use a large-displacement stock block and not  be limited by the rules to
a smaller engine. I figure it also wouldn't make it  past the first three
minutes of tech inspection, if that.

My years in SCCA racing taught me that tech inspectors have absolutely no
sense of humor and often the creativity of a cinder block.

Also, my dad was an engineer at Douglas during WWII and after that, then at
 Aero Commander, then back at Douglas and then when it became
McDonnell-Douglas.  He used to tell me about the TC radials in aircraft in those day and
their  remarkable efficiency. He also noted their remarkable maintenance
issues.

As for the Corona airport mayhaps I'll get out there and take a peek. Lemme
 know which hanger. I promise not to break anything.

These days I'm driving a 2008 MINI Cooper S. One of the best things I've
ever purchased. It's just a giggle to have waiting in the garage. Barbara and
I  are still married; 46 years next month and she's still the love of my
life. Why  she has stayed with me is a mystery for the ages, because she sure
as shit  coulda done mo' bettah.

You take care of yourself, amigo --

Best --

Fuller

I vaguely remember having that conversation with you  about cheating with a turbo compound :)

The TC maintenance issue were mainly about the failing exhaust valves. What is an exhaust valve ? :)

The time to climb engine is still on the dyno at Racing Beat in Anaheim.
Being a one time a PR guy at Mazda USA I am sure you know Jim M.
That is also a story worthy of national media if they come close to the record.
Stuffing 600 horses in a 1500 pound experimental and cooling them is no mean feat.
There could be a title in that :)

I'll let you know when the engine makes it to the hangar and in the airplane.

Paul Lamar


The Rotary Engine News Letter. Powered by Linux.
ACRE NL  web site. http://www.rotaryeng.net.
You Tube  http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights  reserved.