Subject: New Ross Gear Box Laev prop
From: rotaryeng
Date: 7/20/2013, 5:23 PM
To: AAA-rotaryeng


  Guaranteed to be 10 pounds lighter and stronger
  than Tracy's box. Interchangeable with Ross and Tracy gear boxes.
  Fits the new rubber coupling and Jeff's adapter plate with
  the built in main motor mounts. Prop rotates in
  the right direction.


  Paul Lamar

Looks like aluminum tubing with a reinforced ring at the base.

1. Are you planning aluminum piping for the shaft?
2. alignment during welding and cooling may be an issue. Will likely need to build it and line bore it afterwards to ensure alignment.
3. Did you find a piece of pipe that is the same ID as the planet assembly OD?
4. Lubrication?
5. Are you going to be able to incorporate a CS governor?
6. From experience I dont like aluminum welds for structural, fatigue susceptible joints. I have seen to many break. If you are using aluminum pipe for the shaft, the shaft/ flange connection wont be easy. You stated that Tracys shaft was unnecessarily heavy. Maybe so but I doubt it would break in my lifetime. Isn't that worth a couple of lbs? The Lyc/ Cont prop ends of the crank are around 3" in diameter- with the bending moments of this large diameter, it is unlikely that the shaft would fail here. And, with all the work to make the engines lighter there must be a reason for this large, long, heavy, expensive part of the crank.


Lots more questions-

KA

1. No. hardened steel.

2. Yes on machine after welding.

3. Not pipe. Tube! Apples and oranges. The tube will be machined to final size.

4. No oil pressure required as all bearings are anti friction bearings.
Less oil is needed and at low pressure.

5. No. We have to keep the cost down to make it available at all.
High power to weight ratio 2 place  experimental s don't need a constant speed prop. A P-port is much cheaper and worth 50 more HP. A p-port is cheaper by itself than a side port engine due to additional complexity of the four or six runner intake manifold. Set the fixed pitch prop for cruise and take off will be adequate.

Bush planes and sea planes are another matter. In that case NOS is a cheaper solution :) NOS does not hurt an extremely robust rotary engine like the Mazda. Learn how to drift up to the dock with out reverse :) If you insist use an electric prop.

I'll build those two if we get 5 people to put up $5000 each.

6. There are no aluminum parts subject to fatigue in the Ross design.
The Ross design has been used since 1973. There is a turbo 3 rotor Lancair ES with a Ross gear box. There are probably more Ross gear boxes out there than Tracy gear boxes. Tracy's too heavy truck axle shaft was designed for truck vertical shear loads and low cost. There are vertical shear loads in a PSRU.

The Lyc crank is not 3 inches in dia. About 2 and 3/8th. It is done that way beacuse the necessary main bearings are the same dia. Cranks are engineering night mares because of the off set rod journals.

It is easy to forge the whole thing in one piece. The long front part is designed to take the bending load imparted to the shaft by a 50 pound metal prop gyro reaction load. Get a copy of The Sky Ranch Engineering Manual and read up on it.

The Lyc shafts  are not solid. They are drilled out from the prop end.

Also get a copy of Formulas For Stress and Strain. By E. Roark.

I'll be glad to discuss it with you.

Paul Lamar


Hi Paul,
    That is a mighty fine looking prop there, is there any way I can contact the manufacturer ?
            Chris in NZ

It was designed and conceived by me with the help of Butch and Bill. Two very talented engineers on here.
Nobody was willing to pay the price so it never went into productions. It had some neat
patentable features. (Can anybody find them in the dwgs? :)) I chose tig welded 4130 for the
hub as the fatigue strength is much higher than even forged aluminum. Perry Mick on here built the
carbon fiber blades. If we ever go into production the carbon fiber hollow blades will be made in a
high pressure female mold. It is designed to absorb 250 HP.

Paul Lamar

--
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net.
You Tube http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.