Subject: Low cost CD ignition and a1ternator Vespa.
From: rotaryeng
Date: 9/3/2013, 6:30 AM
To: AAA-rotaryeng



Vespa Piaggio motor scooter stator  and rotor has the potential for a
low cost capacitor discharge ignition system.

Milo has done some work on this already using much more expensive
outboard motor parts. Vespa's are made in the millions and the cost
of manufacture is much lower. The parts are pretty much the same as
the outboard parts but smaller.

The secret to this approach is the stator has a high voltage coil
that charges the ignition capacitor. This is a much cheaper and more
reliable way of providing 400 volts for the CD ignition.

Here is a new one on ebay for $105 plus $24 for shipping. Made in
Israel. Complete stator and rotating drum with magnets.

The higher RPM rotary will generate higher capacitor charging
current.

This is a very low cost CD ignition system that will also provide a
low current back up alternator in case the main electrical system
fails.

It is conceivable this will fit in my proposed new Ross copy gear
box.

Paul Lamar


Paul, This variant of CDI was used by Kawasaki for years on their 2
stroke engines. They called it magneto CDI. While the Vespa version
was made in large quantities I would be very cautious about using it
unmodified in an aircraft. The ignition uses a low and high speed
coil to charge the capacitor. The problem with them in high rpm use
is that the magnets overpower the low speed coil above about 2000
rpm. I believe it is refered to as reluctance. The high speed coil
takes over above 2k, but the low speed coil is still in the circuit,
just ineffective. A frequent failure was the low speed coil would
fail with an open circuit. The engine would be fine until you dropped
the rpm below 2k. The engine would then stall and can't be started
unless you can get the rpm over 2k. This failure happened most often
when the engine was used a lot at high revs putting the most strain
on the low speed coil. In a plane this would happen as you were in
approach and the engine would die. I wouldn't mention this if I had
not seen it often. We stocked the coils in bike shops. If your Vespa
dies at low rpm it isn't a big deal, but an engine failure when you
need to go around is. The outboard CDI is designed for constant high
rpm. I would suggest staying with it. Bill Jepson

You have a schematic of that? In theory all you need is one HT coil
like the outboards.

I'll set it up in the lathe and run it at high RPM to see what is
does. The Vespa idles at 1800 RPM :)

I have the Haynes Service and Repair Manual 1991 to 2003 and no
mention of a low speed coil.

The neat thing about the Vespa flywheel is it is made from sheet
metal with no ring gear. Cheap and light weight. Small enough to fit
in the confines of the gear box.

Paul Lamar

Oh Paul, rereading your post you misunderstood what I was writing
about. The spark was handled in the Kawasakis by a standard single
coil that the cap discharged into. The coils I was talking about are
in the stator that CHARGE THE CAPACITOR.  This system didn't require
a battery to operate. Bill

I am aware of all that. The HT coil is in the stator.
It is all in the schematics I uploaded.
Here they are again.

Paul Lamar



Ok. I am surprised that the HT coil is in the stator. I would think there could be interference with the charging coil on discharge. But then there are much better dielectrics now. How would you fit in a second coil? The Vespa is a single right? Maybe I'm missing something.
Bill

Just mount each HT coil 180 degrees apart inside the flywheel and use a Hall Effect sensor
and FET  to discharge the caps.

Paul Lamar-

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.