Vespa Piaggio motor scooter stator and rotor has the potential for a
low cost capacitor discharge ignition system.
Milo has done some work on this already using much more expensive
outboard motor parts. Vespa's are made in the millions and the cost
of manufacture is much lower. The parts are pretty much the same as
the outboard parts but smaller.
The secret to this approach is the stator has a high voltage coil
that charges the ignition capacitor. This is a much cheaper and more
reliable way of providing 400 volts for the CD ignition.
Here is a new one on ebay for $105 plus $24 for shipping. Made in
Israel. Complete stator and rotating drum with magnets.
The higher RPM rotary will generate higher capacitor charging
current.
This is a very low cost CD ignition system that will also provide a
low current back up alternator in case the main electrical system
fails.
It is conceivable this will fit in my proposed new Ross copy gear
box.
You can also buy the High Tension coils separately. Two of those and
a flywheel with magnets are all you need for an ignition system. One
HT coil may not be enough. I have not tried it yet.
Paul Lamar
Hi Paul, On the 12a single rotor I used the Ford Edis4, with fixed
advance. I would be interested in a parts set, that would proved an
aircraft magnito function, installed on front of E-shaft Best
Regards, Rolland
Rolland, We considered the same option you have mentioned for the
magneto to be mounted on the front of the e shaft, but at 9000 rpm
for takeoff am not certain a small magnet rotor like found on the
Piaggio would be strong enough to handle 9000 rpm. Milo
Force in G's = V squared divided by the radius.
V is the velocity of the magnet traveling around the circumference
circle in inches per second. The radius is the radius of the drum.
Weigh the magnet. Bolt one side of the drum to a solid place (mill
table) and apply a tensile force with a hyd jack to the other side.
If that permanently distorts the drum wrap the outside with uni
carbon and epoxy.
When I get a drum in a month of so I will have the dimension and
magnet weight to do that test.
Paul Lamar
Paul,
Found these parts. They were used in a 250 CC 4-stroke, two cylinders
motorcycle engine. Not sure which type but it seems to be related to
GY6 engine used with ATV.
If you want to try them, I can bring them back with me from China
before end of September. They make tens of millions of these for both
domestic and export market.
It has two High Tension Coils instead of one, so more power to charge
up the capacitor.
Henry
That is good news Henry. How much would it cost to mail it? Perfect
for a two rotor.
What is the weight of the flywheel? What is the outside diameter.?
Inside diameter?
I want to calculate how it will hold up at 7500 RPM. Milo is going
for 9000 :)
Mine will not be here from Israel until Oct 1st.
I am thinking of moving the sun gear thrust bulkhead closer to the
sun gear and fit OB Ign in that space. The OB flywheel can be bolted
to the spline plate to drive it. The stator will be bolted to the new
repositioned thrust bulkhead. We then have the option to make the
diameter of the gear box bigger in that area to accommodate the
ignition flywheel.
I can use the turbo 3 rotor test engine to test gearboxes, couplings
and outboard motor style capacitor discharge ignition systems.
I have a 2.17 Tracy gear box that I can modify and use.
Paul Lamar
Found it. GY6 is an original Honda design.
Henry
Don't know how much it weighs. But I will place order today for a
pair just to take a look. Once received, I will weight them. Price
for the pair is very reasonable. I found these from different
vendors, from less than $30 for the pair, to close to $60. There are
so many variety and configurations for the same engine for different
output ratings.
If they work, we should definitely change the connectors to make them
more reliable.
Henry
When I put them in the Ross copy gear box the rotor will be welded to
the new coupler saving some weight on the rotor.
Paul Lamar
Paul, Be careful of welding the rotor, heat can destroy magnetism.
Milo
Yep. I know.
Paul Lamar
Paul,
The rotor/stater pair came in. Unfortunately, they send the wrong
rotor. Too small to fit the stater in. We will return it tomorrow and
he is going to re-send a new one.
Henry
Thanks Henry. What is the diameter of the stator?
Paul Lamar --
Paul,
The stator's outside diameter is 3.475 inch. Thickness is 1 inch, but
we need to add 0.5 inch to account for solder joints and leading
wire.
Henry
Great. That will fit in the new gear box.
Paul Lamar
Paul, need to add 0/75 inch for the Rotor (Magnet) Hope it will
still fit inside. As a bonus, we have an extra small alternator as a
backup :)
Henry
OK That will still fit.
paul Lamar
--
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.