Subject: Mistral engines Paul Janssens Port Inserts
From: rotaryeng
Date: 9/14/2013, 6:34 AM
To: AAA-rotaryeng




  Hi Paul.

  I think you'd like an update on what's happening with my Mistral engine,
  so here goes.

  I've been flying the Glasair since Dec 6 of last year. engine works fine
  and I'm very pleased with it.

  There are still some aircraft electrical signals interfering with the
  engine's sensors, so i'm getting the same warnings during flight, all of
  which I've come to understand quickly, and Mistral will be adapting the
  waring thresholds to suit my installation.

  I'm averaging 54 liters per Hour ( about 13 USG/H ) with mogas, and 0.2
  of a quart of oil. The 300 hp engine is just wonderful.

  My cooling is only just satisfactory. At OAT of 30°C, i do have to
  reduce immediately after gear retraction, and speed up to 140 KIAS so
  get more flow. About 2 minutes into the flight, the heat wave from the
  take-off reaches the sensors, and they'll set off the warning range of
  the system, but i still have enough margin to the alert threshold, and
  in 2 min the wave is cooled out of the system.

  Longest flight so far was 2h 45 min, at FL125 where I had about 53 %
  power remaining. I have yet to experience any trouble with the engine,
  but the ECU's sometimes bug up when i start them up, the remedy is
  simple, power down, wait a minute, and they'll do just fine.

  I have been doing aerobatics, and sustained G-turns to test the oil flow
  with Mistral always checking the recorded data afterwards. Up to 4
  sustained G's is all we did so far, but not a hint of any trouble. The
  Mistral has a wet sump, and we did see the early signs of oil pressure
  loss at values between 0 and 0.5 G, so we have chosen to stay away from
  the region < 1G with this engine configuration.

  I had a problem with MT propeller. they sold me what they said was the
  prop, specially made for this engine, which turns at 2350 rpm at
  take-off, and 2000 in the cruise. What they sold me was an off the shelf
  prop for a lycoming, which turns at 2700 and 2300 resp. so when i
  started doing my dive tests, the prop started overspeeding at around 210
  KIAS. I was a bit surprised, but did some test flights and calculations,
  and presented them with my findings. They initially tried to tell me i
  was wrong, but ended up sending me a mod that allows the prop to go to
  45° pitch, when the original setting was 35°. This clears the overspeed
  issue, and the prop is generally satisfactory, but my calculations still
  tell me I loose 17 % because the prop is turning at 300 rpm below which
  it was intended for, and that it's working at 5° higher angle of attack
  than it's ideal value. So far, MT has chosen to pretend I'm not there
  with regards to that issue. Time will show that to be a mistake.

  Noise....BIG problem.

  Mistral gave me a long absorption muffler from Chabord in France ( the
  one you see in the pictures ). Chabord sells these to be put on
  lycomings, and of course the result on my Glasair is catastrophic. we
  measured 93 DB at take-off, and 87 DB in a cruise setting overflight at
  1000 ft AGL, but that frequency....

  The extension pipe is my request. i didn't want the muffler to hang just
  under the fuel bay in the wing, after all, it's an experimental aircraft
  with retracts.

  Chabord took about a year to build another muffler ( bet ya the French
  take less time when it comes to cooking or making love ), and it was
  even louder than the original. Mistral then tried a tangential muffler
  from Rochhausen in Germany with a dovetail exhaust, on a 200 hp, 2-rotor
  engine, but no real improvement.

  I displayed the aircraft at the big Friedrischafen fair for Mistral
  engines ( you can say it's about like sun and fun, but mostly without
  the sun ). The reactions from the public and professionals were VERY
  positive. Mistral has now shifted their priority to sound reduction as
  they know that they won't be able to sell any more engines like this,
  and the way things stand now, we are rapidly making a bad reputation for
  the product. Clients are lining up for this engine, and there is some
  urgency if we don't want to loose them.

  We have measured frequency ranges on my Glasair, and a theoretical
  simulation will be ordered soon.

  Can you tell me if there has been any significant progress on noise
  surpression on your side of the Atlantic ? Mistral will provide me with
  a good solution in due time, but in the mean time I'm ashamed to fly my
  Glasair because it does disturb people on the ground. I haven't built
  this aircraft to give aviation a bad reputation.

  with kind regards,

  Paul janssens

  Belgium

  Rearrange the cooling system on the right side of the cowl. Put the
rad core
  next to the cowl surface and the diffuser between the core and the hot
  engine to isolate the engine heat from affecting the rad core. Put
vertical
  louvers on the right side of the cowl to let the hot air from the rad core
  escape.  They can be made adjustable to reduce the drag at cruise speed or
  on a cold day.


  This will improve the cooling.

  We have a new coaxial muffler design that works a little bit like a ram
  jet, ejector or thrust augmenter
  so it does not add too much to the aerodynamic drag. The tone of the
  rotary sound is much more pleasant.

  Peter G, I thought you might also be interested in this coaxial muffler
  design speaking of turbo compound.

  Paul Lamar


  Thanks for the update Paul. Glad to hear the 3 rotor is going well. What
  are your oil and coolant temps running at? From memory your main cooler
  is much larger than Tracy's is using on his 3 rotor. He has I believe
  540cu inches of cooler. See photos of his cooler and exhaust setup.

  Steve Izett

  Paul, check your rotor housing for the presence of these Inconel exhaust
  port inserts.  They were used in all normally aspirated 13B's to quiet the
  exhaust.  Mistral built a lot of engines with stock Mazda parts. The 3
  rotor was sold only as a turbo charged engine so it did not have them.
  Breaks up the supersonic shock waves coming out of the open port which is
  all of the time :)

  Paul Lamar

  Here is some more info on the subject.


  Paul Lamar --

  Thanks Paul, yes, the radiator position change was my back-up plan.
I'll try and fly like this, because I don't like the idea of having ugly
louvres in my cowl, especially as that would cover a large surface.
  I have read about the inconel inserts, and wil check if they're there,
not sure.
  Steve, my coolant is at 92°C after take-off on a 30°C OAT day, in
cruise it fairly quickly settles to 84°C. Oil is about 94 - 95°C after
take-off. I try to keep it below the caution threshold of 97° by
reducing, but the max allowable is 102° by Mistral, and even they say
that's conservative. In cruise the oil settles with the coolant at
around 87°C.

  Paul janssens


  Beauty is the eye of the beholder. Form follows function.  If it works
well it is beautiful :)
  Paul Lamar


Thanks for the numbers Paul. They aren't out of the park.

Looks like you have opened up your right cowl cheek in order to get more
air.
As I understand it unless you can get that air out, and create the
pressure differential across the face of the cooler more air in can be
self defeating.
Are you using your cowl flaps?
What difference does lifting your gear make to cooling?
I've wondered about that with ours. Does the opening created by the gear
down provide a negative or positive pressure path for air in the cowl?

I'd come back again to Tracy's 3 rotor 300hp design that we know is
cooling and he has 5.25" - 22sq inch round cheek feed to his cooler.
Even with his diffuser that you saw in the photo, he had uneven
distribution and too much air passing through the very back of the core.
Paul L has been very helpful re cooling.


BUT Paul L, cutting the side of that beautiful cowl!
Where is the artist in you, you butcher!!?


Cheers

Steve Izett

It all depends on the workmanship. If the louvers fit flush with a
constant gap of .050 all the way
around it would be very impressive indeed. I have seen it done.

Paul J, Do you have my book "How to Cool Your Wankel" ?

Paul Lamar


Yes Paul, your book was the bible i used to design my system, thanks for that. I opened up the rhs inlet because i was getting quite a temp rise in the coolant between the first flight, done at 6°C OAT, and a later one at 15°C OAT. I had the cowl flaps installed, but they never made much of a difference. I re-installed them in summer to see if the shape would draw more air out of the cowl, but temp rises made me conclude they reduced the flow through the outlets, so they're off the Glasair now; I may install them for cold weather flying as they allow a quicker warm up before flight. Gear operation doesn't seem to affect the temps, but I haven't really tested. logically, more opening is more cooling, but in this case offset by the need for more power because of the drag of the gear and the higher angle of attack at the gear speeds.
I wondered about the cooling inlets (ram-air fed )and the cowl flaps openings ( venturi sucked ) and if I was about to blow my cowl off the aircraft in a dive. a part in Paul's book gave me an idea. i built a wooden air scoop with the surface of my inlets, and rigged that on the open car roof window, then, i opened the pax door window at the surface of the outlets. then  it was a drive on the highway ( at night, with a cautious run first to scan for speed traps )with the altimeter on the dash. the altimeter showed no change with speed, so all the air was getting out. slowly closing the window i got a pressure increase in the cabin after about1/3 of the surface had been reduced. simple, but it seems to work.
I have no knowledge or capability to do the calculations for a proper system with the absolute minimum of cooling drag, and i know ( feel ) that there is drag there. The external muffler that we're using with mistral for our experiments also eats speed, and until that one is solved i'm just enjoying my plane after 8.5 years of work. I'm getting 180 KIAS on a standard day with 65% power.
incidentally, i had a contact with LMS, a company that does accoustics for some big car makers. My source tells me i the helmholtz system of resonating volumes is the key to our noise problem. He's going to do some simulations for me, and i'll keep you in the loop
Paul janssens

Does your diffuser have a knife edge at the rear where it ends? Also an "S" shaped diffuser has been
reported to work noticeably better than a simple wedge by Ian Beadle in Perth.

I think the largest problem is the outlet of the core is too close to the 3 rotor block. Some dynamic
 pressure could be building on the block. Rethink those louvers :) They will also reduce the cooling
drag as well as in a P51.

The temperate under the cowl directly affects
the core. One degree F increase on the core is a one percent reduction in cooling effectiveness.
Let the diffuser insulate the core from the under cowl temps.

The coax muffler will reduce the drag of the muffler system. I am not sure you got that message.

Also measure the blade thickness near the tips on that prop. The 2300 RPM was chosen to keep
the prop noise down. Most of it comes from the tips going transonic. If you thin the tips and reduce the
local pitch with sanding and carbon fiber the RPM can increase with the same Mach number.
Metal props are 15 MPH faster at Reno than MT props for this reason alone IMHO :)
Tracy Saylor did a back to back test (metal verses MT) in the world's fastest RV6 at 238 MPH.
BTW Dave Leonard did 232 MPH in his turbo 2 rotor powered RV6 at Reno.

I have had discussions on this matter with MT but they think they are smarter than
every body else :) Tip drag rise is why props run into an RPM brick wall.

Paul Lamar


     The Rotary Engine News Letter. Powered by Linux.
     ACRE NL web site. http://www.rotaryeng.net
     You Tube http://tinyurl.com/beqqxas
     Copyright 1998-2013 All world wide rights reserved.