Paul,
Found these parts. They were used in a 250 CC 4-stroke, two cylinders
motorcycle engine. Not sure which type but it seems to be related to
GY6 engine used with ATV.
If you want to try them, I can bring them back with me from China
before end of September. They make tens of millions of these for both
domestic and export market.
It has two High Tension Coils instead of one, so more power to charge
up the capacitor.
Henry
Vespa Piaggio motor scooter stator and rotor has the potential for a
low cost capacitor discharge ignition system.
Milo has done some work on this already using much more expensive
outboard motor parts. Vespa's are made in the millions and the cost
of manufacture is much lower. The parts are pretty much the same as
the outboard parts but smaller.
The secret to this approach is the stator has a high voltage coil
that charges the ignition capacitor. This is a much cheaper and more
reliable way of providing 400 volts for the CD ignition.
Here is a new one on ebay for $105 plus $24 for shipping. Made in
Israel. Complete stator and rotating drum with magnets.
The higher RPM rotary will generate higher capacitor charging
current.
This is a very low cost CD ignition system that will also provide a
low current back up alternator in case the main electrical system
fails.
It is conceivable this will fit in my proposed new Ross copy gear
box.
Paul Lamar
Paul, I could not find the $105 deal on Ebay. Do you have the contact
number for the seller? Milo
Here is a jpg of the ebay add
Paul Lamar
Paul, I can not get that page to come up! milo
Try this
http://stores.ebay.com/Reut1209/_i.html?_nkw=Piaggio+stator&submit=Search&_sacat=Reut1209&_sid=833388452
<
http://stores.ebay.com/Reut1209/_i.html?_nkw=Piaggio+stator&submit=Search&_sacat=Reut1209&_sid=833388452
The store's name is Reut1209. Put that in google.
They have 3277 parts.
They sell the flywheel and stator separately.
They may be sold out of the $105 combo because I cannot find it
again.
The Piaggio Typhoon Sfera and the Zip 50 cc air cooled 2 cycle
engines are the same. 1991 to 2003
You can also buy the High Tension coils separately. Two of those and
a flywheel with magnets are all you need for an ignition system. One
HT coil may not be enough. I have not tried it yet.
Paul Lamar
Hi Paul, On the 12a single rotor I used the Ford Edis4, with fixed
advance. I would be interested in a parts set, that would proved an
aircraft magnito function, installed on front of E-shaft Best
Regards, Rolland
Rolland, We considered the same option you have mentioned for the
magneto to be mounted on the front of the e shaft, but at 9000 rpm
for takeoff am not certain a small magnet rotor like found on the
Piaggio would be strong enough to handle 9000 rpm. Milo
Force in G's = V squared divided by the radius.
V is the velocity of the magnet traveling around the circumference
circle in inches per second. The radius is the radius of the drum.
Weigh the magnet. Bolt one side of the drum to a solid place (mill
table) and apply a tensile force with a hyd jack to the other side.
If that permanently distorts the drum wrap the outside with uni
carbon and epoxy.
When I get a drum in a month of so I will have the dimension and
magnet weight to do that test.
Paul Lamar
Paul,
Finally received the correct rotor today. Total cost is about $11. I
was thinking about carry them to the US for you. But it seems that
due to the magnets installed in the rotor, it is not allowed as
luggage. So we need to figure out a way to ship them. I will try DHL
and see if it is possible. Otherwise, it will have to come in a
boat.
The rotor is about 4.45 inch in diameter, including the space needed
for the rotating triggering magnet on the outside.
It is basically a low cost magneto ignition, if you turn it, it will
generate a high voltage pulse to charge up the capacitor. From my
reading, it works on 2-stroke engine at up to 10,000 rpm. Not sure
about the actual spec. but it should work for your design.
Also, you will need to get CDI module for the motorcycle. Since the
coil will charge the capacitor once per cycle, there is no need to
control the trigger pulse with electronics.
Henry
Send it by boat Henry. My plate is full for the next couple of weeks.
The 3 rotor TC 110 volt ignition is going to take about a week.
Last thing I need to do before I can start the TC up.
When I get it I will build a test bench with a large DC motor
I have that runs up to 10,000 RPM 1t 24 volts.
Paul Lamar