HI Paul & Group,
I'm finally ready to launch my bird after nine years of building. I
took the RX8 rotary powered beast out yesterday and fired it up,
however I managed to foul the spark plugs after starting it a few
times. Went to order new spark plugs this morning and was knocked
for a loop when I was told that the cost would be $20.00 each. No
auto parts store stocks them, so I had them ordered. I tried to
clean them the way I always have with other conventional plugs but
the attempt failed when I tried to re-start my rotary. Do you have
any method to clean them or then wire brush, compressed air & propane
torch? Thanks.
Also, I'm having problems getting the six port RX8 to let me advance
to retard the throttle without it quitting. I'm using Tracy's EC3
engine controller which I find very complicated to program, however
the engine does respond to any input or change I make to the EC3, so
I'm quit sure I have it wired correctly. I'm not sure if I using the
right injector locations on the RX8 six port. I'm using the four
yellow injectors that are located in a row. I blocked off the two
red ports that are located behind to yellow ones. When I removed the
original intake parts I did remove all the inner parts to it. Anyone
know if I'm using the right injectors ports, or have any suggestions.
Many Thanks, Bob Forbes N164WF
The problem is probably not the iridium plugs. The RX8 is notorious for
storing raw fuel
in the rotor housing.
It won't start unless you get that out of the engine. Take the exhaust
manifold
off and insert a small hose connected to a vacuum source to suck the raw
fuel
out of the bottom of the rotor housing. A plastic squeeze bottle will work.
You can also go through the lower spark plug hole. The idea is the get
the small hose to the bottom of the rotor housings.
I would keep the high pressure fuel pumps off for a few rotations of the
engine
when starting from cold. Tracy has never shared the source code on his
EFI so
I have no idea what he is doing about the RX8 starting. Have you
contacted Tracy
and asked him about the stumbling problem when changing the throttle
position.
I am taking his EFI off my 13B powered RV4 and replacing it with a 2
barrel Holley carb.
If you want to keep EFI I recommend changing to Motec or Holley
http://www.motec.com/
http://www.holley.com/Index.asp?division=Holleyefi
<http://www.holley.com/Index.asp?division=Holleyefi>
Paul Lamar
With 15 years listening to people problems with EFI systems I have come
to the conclusion
that it only makes some sense for our applications if you have the
source code and you know
how to program.
By far the easiest programing language to learn is DOS Quick Basic .
3rd grade children learn it easily.
IMHO The best OS to run an EFI/EFIS system is DOS because it is small
very very fast, free and it is real time.
The latest DOS technology is booting very very quickly off a USB stick
and tiny 12 Volt power
supplies. Mother boards are now very small, low cost and very very
powerful due to a huge market
home computer market.
http://www.howtogeek.com/136987/how-to-create-a-bootable-dos-usb-drive/
<http://www.howtogeek.com/136987/how-to-create-a-bootable-dos-usb-drive/>
http://www.pendrivelinux.com/boot-dos-from-usb/
<http://www.pendrivelinux.com/boot-dos-from-usb/>
http://download.cnet.com/DOS-on-USB/3000-2094_4-10795476.html
<http://download.cnet.com/DOS-on-USB/3000-2094_4-10795476.html>
Any body can tune and fix a carb
Paul Lamar
But how long does it take to boot up? Is there a way to have the program
entirely in flash memory so you dont have to go through a long boot up
process?
Most of the single chip boards use compilers that will convert basic,
python, c and many others to assembly for loading into flash on the
board. There is no boot up time- as soon as the board gets power it is
alive and running. If there is something that throws an error like a bad
sensor, the code can be easily written to skip that missing input,
reboot and go from there, in an instant. I have many older computers
here from a school down the road, so at some point I might see how long
it will take for it to boot and start running- but from experience I am
not optimistic about this application.
Paul, have you timed how long it takes for the system to boot up?
As far as the EFI goes, for now I agree with Paul. There currently isn't
a system out that I know of that is plug-n-play. A carb system is
simple, and if you can get the ignition worked out a carb is really
simple. If your aim is to get in the air as simply as possible, a carb
might be the simplest way to go. Kevin Alderman
I'd say less than a second. command.com is less than 64K bytes. Not
gigs. I wrote a moving map program
in DOS QB compiler that was less than 64K. It pretty well comes alive
when you turn it on.
Next time it is up and running I'll time it. I can read all the files in
my linux computer merely by plugging
in the USB stick.
EFI is a huge psychic energy sink.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net.
You Tube
http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.