Subject: Follow up propeller and pictures
From: rotaryeng
Date: 9/19/2013, 4:52 AM
To: AAA-rotaryeng





Hi Paul,

I started to fly my RV-7A, even with the help you provided, It took 9 years
and 4 months and I still have finish work to do, Probably a year worth of
work.

I have one major issue with the propeller: Wood prop D = 76 in, Pitch = 88
in, Static RPM = 5700

No increase in RPM with speed increase, Take off takes over 1500 feet Top
speed 105 mph

I tried a Wood prop D = 69, P = 56, Static RPM over 7300 Could not fly it
because of vibration.

What would you suggest?

Thanks,

JP


Assuming you have a 2.85:1 gear box cut 4 inches off the first wood prop
diameter and rebalanced it.

Balance the second wood prop and try it again.

Pass a round bar through the hub and use horizontal and parallel steel bars
to static balance it.

Take some pictures of the intake manifold and email them to me.

Put the word "PRIVATE" in the email subject box if you don't want me to
publish them.

Paul Lamar


paul, curious: what's the interest in the intake? novice here, excuse me if
is stupid question........
jess


The key to tuning a rotary engine is the design and construction of the
intake manifold.

18 inch 2" OD  runners and a p-port is optimum.
Anything less that this is less power.

Paul Lamar



Good night Paul,

As promised, see pictures attached.
By the way, I cut my prop 1.5 inches today, Ground test looked good, will
fly it tomorrow if weather is fine.
Will cut another half inch if needed, will see!!!


PS, I am sending one picture, otherwise, may not go thru.


Thanks a lot

JP

What is inside the large box bolted to the side of the block?

P-port or side port?

If  each port does not have an individual long runner or tube there will be
very modest amount of  HP generated.

With no tubes or runners one would be lucky to see 100 HP.
The optimum length for the tubes or runners is around 18" with side ports or
P-ports.

If a side port engine is 200 HP a  p-port version will be 250 HP.


Shorter runners than 18" indicates the max power will occur higher than 7500
RPM which is not good for a 2.85:1 gear box.



Paul Lamar


This is a 13lb piece of aluminum with holes for intakes and injectors (side
port).
The runners are part of this piece, they are about 6 inches long.
I attached the solid work drawing.
I do not know what power it is supplying yet, I just cut the prop yesterday,
may try it today.
Always start first shot, idles at 1800 RPM; mixture easy to adjust; I was
hoping to get 160 hp.
On my first attempt I had long runners, but my lay out was messy and I could
not fit everything under the cowl,
The engine was not stable, RPM was changing by itself all the time, mixture
did not work well.

JP

I assume you have Tracy's EFI :)


The "not stable, RPM was changing by itself all the time, mixture
did not work well." Had nothing to do with the long runners :)

Where were you monitoring the intake manifold pressure?.

That makes a huge difference with Tracy's system.
As far as I know he does not take multiple readings to average
them. That is one of the problems with that method of controlling the
mixture.

The best place is the oil injector holes in the rotor housings.
This gives the most stable readings as that is the amount of air
actually getting into the engine. The orifice should be small to even
out the pressure variations.


The EFI world switched to mass airflow sensors years ago :)
Scrap Tracy's system and get a Motec with mass airflow sensor.

The six inch runners put the torque peak way beyond 7500 RPM.

I cannot estimate the HP until the runners are long enough to work.

18 to 20 inch runners put the torque peak at about 6000 RPM
and the HP peak at about 7500 RPM.

Also your throttle body is a bit over size.

Is it six side ports or four side ports?

Can you send that file in IGES?


You have plenty of room for long runners if you do it this way.
P-port or side port.

I notice you are using the quick and simple cooling system under
the fuselage. How is that working?

Paul Lamar
-- 

 The Rotary Engine News Letter. Powered by Linux.
 ACRE NL web site. http://www.rotaryeng.net
 You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2013 All world wide rights reserved.