Subject: Cut down Holley 2 bar
From: rotaryeng
Date: 10/14/2013, 1:17 PM
To: AAA-rotaryeng




       This is coming along well. I will need a bump on the cowl but it
   can do
       double duty as a cold air scoop.

       I got rid of an amazing amount of stuff when I took out Tracy's EFI.
       It  is now almost as simple as an aircraft engine.

       Paul Lamar



   Paul,

   What does the Holley and leaning block weigh? Simple is good in the air.

   Regards,

   Matt

   About 5 pounds but that is off set by the weight of a throttle body,
   four injectors
   and computer. Not far from a wash.

   Here is  how much sticks out of the cowl roughly.

   Paul Lamar


Paul, you can mill the choke tower off for better airflow with a low
profile carb hat; its standard practice on blow through turbo setups
with Holleys.

Everett Rankin


I was wondering about that. Thanks for the tip. Will do.

What does that .25 inch dia. steel tube do that comes straight out of
the top ?
Can I cut that off too?

Paul Lamar

That is your vent for the float bowl. If it is too low you take the
chance of fuel spilling out. But there are modifications that can be
done there to accomplish your needs.

Bob Mears

As Lyn mentioned.

I'll connect a small hose to it. If I point it into the direction of the
air flow into the carb
I will get this much increase in total pressure above the fuel.
That will richen the mixture above and beyond what the venturi can suck out
of the float bowl.

MPH         PSI
  50            0.0
  60            0.1
  70            0.1
  80            0.1
  90            0.1
  100           0.2
  110           0.2
  120           0.3
  130           0.3
  140           0.4
  150           0.4
  160           0.5
  170           0.5
  180           0.6
  190           0.7
  200           0.7
  210           0.8
  220           0.9
  230           1.0
  240           1.0
  250           1.1
  260           1.2
  270           1.3
  280           1.4
  290           1.5
  300           1.6
  310           1.7
  320           1.8
  330           2.0
  340           2.1
  350           2.2
  360           2.3
  370           2.5
  380           2.6
  390           2.7
  400           2.9

Programed in QB64.

Paul Lamar


I can do this for about $50.
Only 3.25 inches high. Should fit under any cowl. I got a about another
half pound
out of it. Only a slight bump in the RV4 cowl. Good for 500 CFM.

Jeff is working on a new manifold design for six port RX8 engines. These
engines are the most
popular. Mazda stoped selling the 4 port RX8 motor about 2006. The outer
2 ports are
combined into one 2" OD aluminum tube. Will work with EFI or a carb.

I can build a manifold to your design for carb or EFI. Over the top, all
on wide side or what ever.

Paul Lamar

I just cut some more off the Holley. There is amazing amount of material
that does  not do anything and holes that go no where once you get rid of the choke.

 The bump in the cowl is getting smaller.

More to go.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net.
You Tube http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.