Pull the plug on the cast in oil gallery and tap to 3/8-18. Don't
over do it as you could crack the cast iron front end housing. People
claim taking the oil out of here (rather than the front cover) going
to the oil cooler reduces the oil temp 10 F. Several sharp 90 degree
turns eliminated.
Fast moving fluid does not like 90 degree turns.
Unsubstantiated.
Paul Lamar
Paul, I used my CCM (Cheap chinese Mill) to make an aluminum block
with an "O" ring recess (to seal to the end hsg) and a pipe thread
port (for the hose fitting) to bolt to the hsg useing existing studs
(like "Mistral" did)..
I also drilled the oil gallery slightly larger as I felt that a
3/8-18 fitting was too restrictive but is about all could be done
without the danger of cracking the hsg and making expensive junk out
of it..
I have seen the suggestion somewhere of threading this area for a
pipe thread but if the tapered pipe tap does not crack the hsg then
the fitting itself probably will if tightened enough to prevent
leaking..
Kelly Troyer Dyke Delta_"Eventually" 13B_RD1C_EC2_EM2
Use an aluminum pipe thread and use Teflon tape. The aluminum is soft
enough not to crack the cast iron.
Some housing are already taped and have a steel pipe thread plug in
them. Both Mike's turbo engine and the 3 rotor I have both are
taped.
Here is the Mistral system pictures.
Paul Lamar
I used the base of a spark plug with straight threads and integral
seal washer. Brazed the plug base to an AN -10 male fitting.
Robert
--
Good idea.
BTW Robert have you been for a ride in Dave Leonard's turbo RV6?
He is in your neck of the woods.
Paul Lamar
You face off the end of the "As cast" feature and prepare the hole
for a
straight thread "Tube to Boss" fitting. An "O" ring seals the fitting
not the wedge effect of a tapered pipe fitting. The spark plug idea is
about the same thing. This eliminates the "O" ring junction between the
iron and the front cover that fails so often in cold starts. Replace
that "O" ring with a thick aluminum disc. About .050" to .060" to seal
the junction.
While you have the iron clamped in the mill, do that same thing to the
gallery above, and run an oil line direct to the front stationary gear
and bearing. Leave the dowel gallery open and have two oil lines
feeding
the front stationary gear. The front bearing fails first when oil
pressure is very low or lost. Feed this oil line from the aluminum
block
on the oil filter stand.
Because we use an external pump, we do not do the first mod. The front
aluminum housing has a plug at the oil out hole. But all Daryl Drummond
(and many other builders) engines use the second mod.
Lynn E. Hanover
Don't get the idea this is essential for an aircraft engines. The
racers, like Lynn, are turning 11,000 RPM
and spending most of the time 8500 to 11,000 RPM.
We see up to 7500 RPM for take off and cruise at 4500 to 6000.
Paul Lamar
The question is begged,
Is it more important to know the pressure of the oil leaving the pump or
to know the pressure of the oil entering the journals after being
diminished by the pressure regulator ball valves?
Rich
Journals. I just needed a quick and simple oil pressure gage for the
turbo compound engine.
Paul Lamar
There is a need to read the oil pressure at the worst case location in
the system. In the stock system there is some length of oil line and a
cooler between the pump and the oil filter. Oil enters at the bottom of
the outer gallery through the banjo fitting. Thence upward to the filter
stand and the oil filter, or adapter to take oil to the filter, or
filters. The stock oil pressure sensor is located just above the Banjo
fitting. So the actual oil pressure at or close to a main bearing
remains unknown.
I take oil pressure out of the aluminum block that replaces the filter
stand. The inner oil gallery that runs down to the rear main bearing is
fed from this location and provides as close a look as is possible.
The oil temperature sensor is there as well. This is not ideal as it is
close to the rear main bearing but not the front main bearing. Again the
horizontal drilling into the front main is as far from the oil pump as
you can get and is the worst case condition. The rear main is close
enough for me. I use 100 PSI. FAs had 71.1 PSI. FBs had 71.1 PSI. FDs
had 110 PSI. The Racing Beat P/N for an 80 to 85 PSI relief is 11810.
The very early relief valves can be disassembled and the spring shimmed
to provide any oil pressure you might want. Later valves have the top
welded on. Consult your Racing Beat catalog. A free download from the
Web site.
Lynn E. Hanover
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net.
You Tube
http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.