Subject: RX8 tension bolts Old pictures
From: rotaryeng
Date: 11/7/2013, 9:34 AM
To: AAA-rotaryeng




   I have not heard any bad things about RX8 tension bolts so far
   but it might be a good idea if you have an RX8 engine to remove
   the bolts one at a time and coat them with silicone rubber.
   Then replace them  after you accomplish that for each one.
   Do this one at a time so you don't  affect the stock sealing between
   end housings and rotor housings.

   13b engine tension bolts would vibrate and fatigue if you ran
   the engine at high power at a fixed RPM.

   One step up from this was to replace all the stock 10 mm (.394") bolts
   with half inch bolts. It take a special drill jig to drill out the
   end housings. Mazdatrix has such a drill jig.

   The latest trick, with custom aluminum end housing, is use a long
   steel rod threaded on both ends and use nuts on both ends.

   This removes the bending loads due to vibration on the threaded portion
   of the tension bolts screwed into the front end housing.

   If you want your engine to last more than 15 years install Iannetti
 ceramic
   apex seals. Projected life for the ceramic apex seals is then 20,000
 hours.

   Not 2,000 hours.....20,000 hours!

   However I have no idea how long the side seals would last.
   My suggestion is use Mobil 1 fully synthetic oil in the sump.
   I have years of experience with this oil in my street cars and
   the engines last over 300,000 miles while a lot of
   the stuff on the engine failed and had to  be replaced.

   Of course mix 2 cycle oil with the fuel to lube the seals.


   Paul Lamar

   Paul,

   I do agree with the silicone trick, this was done on Norton's to very
   good effect, a good blob of medium to low modulus silicone near the
   centre area of the engine raised the failure events to  20,000 miles of
   high speed work, we did have a resonance at around 7000 rpm and if the
   bike was worked in a zone close to this a engine stud would let go
   within around 200 miles, failures tended to be on the overrun or just
   commencing of.

   Bob

   That is interesting. I did not the Norton suffered from the same problem.

   When we go up to a half inch several good things happen. The resonant
   frequency goes way up   and the bolts are a slip fit in rotor housings
 absolutely
   stopping them from  vibrating. They also act as 17 locating dowels.
 Late 280 HP turbo 3rd  gen 13B's cracked the  rear housings around the
 upper dowel pins until Mazda beefed that area up.

 The torque from the front rotor was twisting the entire engine.

   They are also stiffer in tension helping the housing to housing sealing
   in theory.

   Paul Lamar

       A heavier bolt, thicker bolt ? Would not the resonant frequency
      go DOWN ? Virg

 Maybe I was wrong about that. Low notes on string instruments
 are thicker are they not? I am no musician.

 Paul Lamar


     Yes. GM had a problem with the generator brackets breaking. the
    fix was a thicker bracket. NO FIX. The problem was  the frequency
     was lowered and the bracket broke sooner. A thinner bracket raised
    the resonant  frequency out of the engine range. No more breaking.
    Heard this from Gene Abbey, GM Engineer,
Virg

Was it a round bar?
The devil is in the details. Just making it heavier is not enough.
One needs to know the design. Do you have a dwg?
The extra weight must be used to increase the stiffness.

As I recall low note strings on musical instruments are wound with
smaller wire that adds weight but not bending stiffness.

The bending stiffness of a rod  goes up with the fourth power of
the radius while the weight only goes up with the square.

Paul Lamar


 The Rotary Engine News Letter. Powered by Linux.
 ACRE NL web site. http://www.rotaryeng.net
 You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2013 All world wide rights reserved.