Subject: RX8 tension bolts Old pictures
From: rotaryeng
Date: 11/7/2013, 10:03 PM
To: AAA-rotaryeng



I have not heard any bad things about RX8 tension bolts so far but it
might be a good idea if you have an RX8 engine to remove the bolts
one at a time and coat them with silicone rubber. Then replace them
after you accomplish that for each one. Do this one at a time so you
don't  affect the stock sealing between end housings and rotor
housings.

13b engine tension bolts would vibrate and fatigue if you ran the
engine at high power at a fixed RPM.

One step up from this was to replace all the stock 10 mm (.394")
bolts with half inch bolts. It take a special drill jig to drill out
the end housings. Mazdatrix has such a drill jig.

The latest trick, with custom aluminum end housing, is use a long
steel rod threaded on both ends and use nuts on both ends.

This removes the bending loads due to vibration on the threaded
portion of the tension bolts screwed into the front end housing.

If you want your engine to last more than 15 years install Iannetti
ceramic apex seals. Projected life for the ceramic apex seals is then
20,000 hours.

Not 2,000 hours.....20,000 hours!

However I have no idea how long the side seals would last. My
suggestion is use Mobil 1 fully synthetic oil in the sump. I have
years of experience with this oil in my street cars and the engines
last over 300,000 miles while a lot of the stuff on the engine failed
and had to  be replaced.

Of course mix 2 cycle oil with the fuel to lube the seals.


Paul Lamar

Paul,

I do agree with the silicone trick, this was done on Norton's to
very good effect, a good blob of medium to low modulus silicone near
the centre area of the engine raised the failure events to  20,000
miles of high speed work, we did have a resonance at around 7000 rpm
and if the bike was worked in a zone close to this a engine stud
would let go within around 200 miles, failures tended to be on the
overrun or just commencing of.

Bob

That is interesting. I did not the Norton suffered from the same
problem.

When we go up to a half inch several good things happen. The
resonant frequency goes way up   and the bolts are a slip fit in
rotor housings absolutely stopping them from  vibrating. They also
act as 17 locating dowels. Late 280 HP turbo 3rd  gen 13B's cracked
the  rear housings around the upper dowel pins until Mazda beefed
that area up.

The torque from the front rotor was twisting the entire engine.

They are also stiffer in tension helping the housing to housing
sealing in theory.

Paul Lamar

A heavier bolt, thicker bolt ? Would not the resonant frequency go
DOWN ? Virg

Maybe I was wrong about that. Low notes on string instruments are
thicker are they not? I am no musician.

Paul Lamar


Yes. GM had a problem with the generator brackets breaking. the fix
was a thicker bracket. NO FIX. The problem was  the frequency was
lowered and the bracket broke sooner. A thinner bracket raised the
resonant  frequency out of the engine range. No more breaking. Heard
this from Gene Abbey, GM Engineer, Virg

Was it a round bar? The devil is in the details. Just making it
heavier is not enough. One needs to know the design. Do you have a
dwg? The extra weight must be used to increase the stiffness.

As I recall low note strings on musical instruments are wound with
smaller wire that adds weight but not bending stiffness.

The bending stiffness of a rod  goes up with the fourth power of the
radius while the weight only goes up with the square.

Paul Lamar


No, It was the bracket that adjusted the  belt tension for the
Generator. By the way, Gene worked in the Pontiac Division,

Virg

Without DWGs no telling what happened. Did Gene see my mid engine
Firebird I built for Pontiac back in the early 70's? :)

http://www.rotaryeng.net/Mid-engine-Firebird.pdf

Paul Lamar

   I do not know. He was working installing LINK Flight Simulators
   when I met him at Eastern Air Lines, Virg
-

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.