Subject: Aussie multi spark cap discharge 13 times !!!!
From: rotaryeng
Date: 11/17/2013, 6:56 AM
To: AAA-rotaryeng


I met Aden Lindsey in Perth at the Perth aircraft rotor head club dinner.
Aden teaches electronics at the local college as I recall.
Ian flies all over the Aussie outback in an RX8 powered RV6 as part
of his job as a radio transmitter repair man..

http://www.youtube.com/watch?v=XgLw3a8DZgM

Aden sent me a cap discharge ignition system designed by John Clarke and
published in Sept 1997 in Silicon Chip mag. An Aussie mag.

It worked for awhile quite well then the push pull HV supply failed as they
are want to do. Something to do with imbalance in  the transformers.
One of the very attractive features to me was the high side switch that
prevented the FET from shorting the HV supply when it discharged the
cap through the coil. I addressed that issue in my power supplies by
putting a series power resister in the line that charges the cap. That has its
drawbacks. Mostly it affects the overall efficiency. However it  is simple and it
works.

   So I am working on reproducing that second half of the Aussie
circuit. I have two HV supplies that are working well. One is wall
powered and the other a 12 volt powered flyback design. High side switches are hard to
design and highly prone to failure. The IR2155 half bridge driver chip  has of necessity a
high side switch.

This chip was used used in the Aussi design and has been replaced by a
more advanced version. One might ask what is a high side switch? A high side switch is
used between the load and the the supply. A far more common low side  switch is used
between the load and ground.

SNIPS .....


Paul Lamar

The D6 1n4936 is a fast recovery rectifier. Along with C1 and the
unlabelled 3 resistors are a charge pump ckt to raise the Vb (Vboost)
input 15V above the 300V source. A commonly used ckt with half bridge
drivers because Ho must drive Q6 gate up to 315V to saturate Q6.

Robert.


You are right. I don't know how I got the idea it was a zener.
Did I get that way wrong or what? It would have helped if he had
labeled the high side floating supply line with 315 volts.
Makes sense because of C1 being only 16 volts.
Those resisters are 33K one watt.

Does that mean I do not have to regulate the 300 volt supply?
That is good news and encouraging indeed. Major reliability issue.

It is a real help with you on here Robert. I am glad you are interested
in this stuff. I need all the help I can get.

Are you doing your email with a cell phone?
Do you have a pdf viewer? I sent a pdf of the Silicon Chip
article.

Here is a corrected schematic.

Paul Lamar

If my arithmetic is correct we can fire the plugs every 20 degrees

13 TIMES AT 8,000 RPM!!!!!!!!!!!!!!!!!!!!!!

Up to this time piston engine ignition technology has been applied to the
rotary. The fundamental difference is the fire moves PAST the spark plugs
in a rotary in 270 degrees of e-shaft angle  while it moves AWAY from the
spark plugs in only 90 degrees of crank angle.

It is just common sense to fire the plugs every 20 degrees to ignite
that hydro carbon rich mixture on the back side of the flame front.

No way would inductive smart coil technology work here!
It takes 4 msec just to charge the coil each time it is fired.

I would not be surprised if this MS ignition system significantly improved
the BSFC of the rotary throughout  the rev range.

Paul Lamar



 The Rotary Engine News Letter. Powered by Linux.
 ACRE NL web site. http://www.rotaryeng.net
 You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2013 All world wide rights reserved.