Hi
I'm inventor at Korea.
As my calculation using ceramic rotor and housing make no cooling
system or extremely less cooling system.
In that case efficiency and power get much better.
and I also considering using superalloy for that. like Inconel.
I need opinion of yours.
puru puru
It is worth a try.
Paul Lamar
Hello everybody!: I guess that Mazda conducted some research on a
similar concept, they called it: 'Adiabatic Wankel type Rotary
Engine', SAE paper 860616 by R Kamo and R M Kakwani is about this. As
the subject of improving ignition in Wankel RCEs came recently to
this forum, I'd like adding some references that may have a
connection to this, all SAE papers:
920303: 'Heat transfer and performance characteristics of a
Dual-Ignition Wankel Engine', M S Raju (Sverdrup Technology, Inc)
920304: '3-D Computations to improve combustion in a
Stratified-Charge Rotary Engine Part III: Improved Ignition
Strategies', J Abraham (John Deere) and F V Bracco (Princeton Univ)
930680: 'Catalytic Glow Plugs in the JDTI Stratified Charge Rotary
Engine', Dylan Hixon et al (Precision Combustion Inc)
2001-01-1844/4263: 'Research and Development of a Direct Injection
Stratified Charge Rotary Engine with a Pilot Flame Ignition System',
Takumi Muroki et al (Kanagawa Institute of Technology and Chiba
University)
It doesn't deal with the same, but the title of this SAE paper sounds
good to me: 860562: 'Experimental evaluation of Rotary Engine Timing
Gear Loads', Mark R Kulina (John Deere)
In the issue of rotor temperature affecting favorably several things:
HC emissions, BSFC, perhaps the reduction in exhaust HC may allow to
a fuel/air ratio more favorable for fuel economy; in China, professor
Teluan Chen headed a large multi-centric research about RCEs,
published in SAE paper 880628, one of the models proposed in the
article as having good performance used a PP with a Reed-Valve
control, directly sending the fuel:air mix towards the hot surface of
Rotor, this helping in Vaporization of gasoline, Rotor cooling, and
fuel economy and emissions results.
Hope somebody finds an interest in this; if testing some of these
ideas, tell us about results, please. Thanks for your attention. Nice
year 2014.
Salut † Jose Gros-Aymerich Madrid, Spain
Reed valves are not needed with side exhaust ports. On peripheral
intake port the airflow never really stops due to the inertia of the
air molecules so the reed valve would not function. As the narrow
apex passes over the intake p-port the next chamber in line starts
receiving air as the first chamber is closing.
Reed valves are obsolete tech.
www.rotaryeng.net/Adiabatic-rotary.pdf
http://papers.sae.org/860616/
http://www.sbir.gov/sbirsearch/detail/72100
http://ceramicrotaryengines.com/
http://link.springer.com/chapter/10.1007%2F978-1-4757-9348-2_6#page-1
Paul Lamar
Thanks Paul: your comments are always sound, but as you can see
in the attached patent granted to Ford in 1979, a Reed-Valve in
a Peripheral Intake Port may be of some help, attached is also
the image of the results obtained by Yanmar Diesel with major
and minor Reed-Valves, and in a PP, the inherent possibility of
exhaust gas recirculation, because of the overlapping of intake
and exhaust openings, the intake ducts having a lower pressure
than the exhaust at partial load and low rpm, this allows EGR,
causing misfirings and poor MEP, all this being improved by a
R-V, that also would generate some kind of an 'super-charge'
effect, because of the opening and closing overflows, in the
style of an 'hydraulic ram'.
As you know, an early opening of a PP gives better low rpm
performance, but a late close gives better results at high rpm,
both stated as º before or after 'TDC', and a R-V would act as a
variable timing intake, always giving the best results, the
intake time would close when no more mix would enter the working
chamber, and blow-back to intake manifold would be prevented,
this allows placing the intake port for top rpm power, and also
having the low rpm advantages, as the RV closing in connection
to the difference in pressures of the intake port and the
working chamber, it's the same as an early geometrical closing
of intake port would yield.
All charts published in many places, I don't send it here, show
that the difference in volumetric efficiency at low and high rpm
of a PP is much larger than in a side intake port approach, BMEP
in PPs is always greater than with SPs, and besides the data
published by Yanmar Diesel, the Toyota SAE paper, the results of
the Norton engine, that having the carburetor butterfly close to
the housing working surface acts as a non return valve, I had a
letter from D W Garside that indicates that from data received
from other RCE builders, R-Vs improve low end performance, but
are somehow worse at high rpm, and for a company building
motorcycle engines, as well as for most of the persons asking
questions or making comments in this forum, who focus on
airplane engines, the situation is different, but my main if not
only interest is car engines.
But I guess we discussed all this before.
Thanks for your kind attention, have a nice year 2014. Best regards.
Salut
Jose Gros-Aymerich
Madrid, Spain
Reed valves are a dead end Jose. They add weight, cost and cut the air
getting
in the engine. Less air less HP. In the RX8 engine there is no valve overlap
at all.
The engine will smoothly pull the car away from 600 RPM idle
with out depressing the throttle pedal. Manual transmission.
I have one and I demonstrated that many times to a car full of people.
There are at least several hundred thousand RX8's out there.
Borrow one and drive it.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.