Subject: ceramic rotor and housing
From: rotaryeng
Date: 12/30/2013, 8:58 AM
To: AAA-rotaryeng


Hi

I'm inventor at Korea.

As my calculation using ceramic rotor and housing make no cooling
system or extremely less cooling system.

In that case efficiency and power  get much better.

and I also considering using superalloy for that. like Inconel.

I need opinion of yours.


puru puru

It is worth a try.

Paul Lamar


Hello everybody!: I guess that Mazda conducted some research on a
similar concept, they called it: 'Adiabatic Wankel type Rotary
Engine', SAE paper 860616 by R Kamo and R M Kakwani is about this.
As the subject of improving ignition in Wankel RCEs came recently to
this forum, I'd like adding some references that may have a
connection to this, all SAE papers:

920303: 'Heat transfer and performance characteristics of a
Dual-Ignition Wankel Engine', M S Raju (Sverdrup Technology, Inc)

920304: '3-D Computations to improve combustion in a
Stratified-Charge Rotary Engine Part III: Improved Ignition
Strategies', J Abraham (John Deere) and F V Bracco (Princeton Univ)

930680: 'Catalytic Glow Plugs in the JDTI Stratified Charge Rotary
Engine', Dylan Hixon et al (Precision Combustion Inc)
2001-01-1844/4263: 'Research and Development of a Direct Injection
Stratified Charge Rotary Engine with a Pilot Flame Ignition System',
Takumi Muroki et al (Kanagawa Institute of Technology and Chiba
University)

It doesn't deal with the same, but the title of this SAE paper
sounds good to me: 860562: 'Experimental evaluation of Rotary Engine
Timing Gear Loads', Mark R Kulina (John Deere)

In the issue of rotor temperature affecting favorably several
things: HC emissions, BSFC, perhaps the reduction in exhaust HC may
allow to a fuel/air ratio more favorable for fuel economy; in China,
professor Teluan Chen headed a large multi-centric research about
RCEs, published in SAE paper 880628, one of the models proposed in
the article as having good performance used a PP with a Reed-Valve
control, directly sending the fuel:air mix towards the hot surface
of Rotor, this helping in Vaporization of gasoline, Rotor cooling,
and fuel economy and emissions results.

Hope somebody finds an interest in this; if testing some of these
ideas, tell us about results, please. Thanks for your attention.
Nice year 2014.

Salut †      Jose Gros-Aymerich Madrid, Spain

Reed valves are not needed with side exhaust ports. On peripheral
intake port the airflow never really stops due to the inertia of the
air molecules so the reed valve would not function. As the narrow
apex passes over the intake p-port the next chamber in line starts
receiving air as the first chamber is closing.

Reed valves are obsolete   tech.

www.rotaryeng.net/Adiabatic-rotary.pdf‎

http://papers.sae.org/860616/

http://www.sbir.gov/sbirsearch/detail/72100

http://ceramicrotaryengines.com/

http://link.springer.com/chapter/10.1007%2F978-1-4757-9348-2_6#page-1



Paul Lamar

Thanks Paul: your comments are always sound, but as you can see in
the attached patent granted to Ford in 1979, a Reed-Valve in a
Peripheral Intake Port may be of some help, attached is also the
image of the results obtained by Yanmar Diesel with major and minor
Reed-Valves, and in a PP, the inherent possibility of exhaust gas
recirculation, because of the overlapping of intake and exhaust
openings, the intake ducts having a lower pressure than the exhaust
at partial load and low rpm, this allows EGR, causing misfirings and
poor MEP, all this being improved by a R-V, that also would generate
some kind of an 'super-charge' effect, because of the opening and
closing overflows, in the style of an 'hydraulic ram'.


As you know, an early opening of a PP gives better low rpm
performance, but a late close gives better results at high rpm, both
stated as º before or after 'TDC', and a R-V would act as a variable
timing intake, always giving the best results, the intake time would
close when no more mix would enter the working chamber, and blow-back
to intake manifold would be prevented, this allows placing the intake
port for top rpm power, and also having the low rpm advantages, as
the RV closing in connection to the difference in pressures of the
intake port and the working chamber, it's the same as an early
geometrical closing of intake port would yield.

All charts published in many places, I don't send it here, show that
the difference in volumetric efficiency at low and high rpm of a PP
is much larger than in a side intake port approach, BMEP in PPs is
always greater than with SPs, and besides the data published by
Yanmar Diesel, the Toyota SAE paper, the results of the Norton
engine, that having the carburetor butterfly close to the housing
working surface acts as a non return valve, I had a letter from D W
Garside that indicates that from data received from other RCE
builders, R-Vs improve low end performance, but are somehow worse at
high rpm, and for a company building motorcycle engines, as well as
for most of the persons asking questions or making comments in this
forum, who focus on airplane engines, the situation is different, but
my main if not only interest is car engines.


But I guess we discussed all this before. Thanks for your kind
attention, have a nice year 2014. Best regards. Salut Jose
Gros-Aymerich Madrid, Spain

Reed valves are a dead end Jose. They add weight, cost and cut the
air getting in the engine. Less air less HP. In the RX8 engine there
is no valve overlap at all.

The engine will smoothly pull the car away from 600 RPM idle with out
depressing the throttle pedal. Manual transmission. I have one and I
demonstrated that many times to a car full of people.

There are at least several hundred thousand RX8's out there. Borrow
one and drive it.

Paul    Lamar


Thank you Paul: Yes I've driven an RX-8, but as the man
from Mazda told me tires were not in good condition, I didn't go
any further than a turn around the block.  I'm waiting for a
tuned 1988 13B non turbo to arrive, checked and tuned by Kevin
at Rotary Resurrection, as I bought also two sets of housings,
I'll try finding someone to modify one of the sets to a
rectangular shaped Peripheral Port, and I'll add on each PP a
Reed-Valve for a 2-Stroke Snowmobile, equal in type to the ones
described in the Ford's patent, I'm looking also for a suitable
R-V to be adapted to the side plate of a KC-27 engine, where the
admission hole for manifold from carb is located.  When I have
results of both, I'll let you know.  Some people have fun by
gambling, or by attending rock concerts, buying gems, or
traveling to far away places, I like this kind of mechanical
experiments, that is just an equivalent of the good old Meccano,
but full size, and a bit more costly; that's all, it's just a
game I play for fun, please don't arrange to have me sent to no
asylum, I'm just as sane as anyone.


Nice year 2014. Salut     Jose Gros-Aymerich
                                        Madrid, Spain

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2013 All world wide rights reserved.