Hi Paul, Do you have any more info on Tracy's box, like the shaft
and internals, I can't figure out where the thrust goes etc. The box
is very chunky, I would say overkill somewhat. Also I can't see any
oil supply, in or out. You wouldn't have to saw off the flange, I
would do my box and then remove it from the pattern before casting
others.
From the side view it looks like the prop shaft is one piece, is
this right ? Also, is the box intended to be bolted up to a plate or
a bell housing. Chris.
Tracy used a cut down GM pick up truck rear axle and ball bearing.
The bearing was retained by a pressed on collar with several tons
of force. Tracy fed the box with oil from the engine. So too the
Ross but the Ross had all needle bearing so it required less oil.
Very heavy at 9 pounds, I would not do it that way.
I would use a hollow shaft like the Ross with a separate prop
flange. No forging required. The flange would be retained by special
set screws called "Extended Point" . A relatively new idea and much
stronger than pins that go all the way trough the walls of the
shaft (which is what Ross used for years) or splines and much less
cost. Easy to machine with a rotary table.
About a 2 inch OD steel tube with a .190 wall is about right. Just
like the Ross box. That is about the largest needle bearing you can
buy.
Use about eight or ten of these .25 inch screws and they are almost
as strong as a one piece shaft and flange. Here are some pictures.
Do you use a dwg program Chris? If not I suggest getting a Rhino. It
will save you money in the long run.
Paul Lamar
Speaking of the Ross PSRU, if one just decided to cast his own
housing [perhaps out of an aluminum alloy], what would be the best
alloy to useā¦decent properties and not too expensive or hard to do?
Gene Kahn
356 is the usual casting alloy and the foundry heat treats to T6
hardness. Paul Lamar
I have been following this discussion as this is something I was
thinking of trying. At first I thought it would be easiest to simply
copy Tracy's 2.85 box because it seemed easier to plug a shaft into
the planet gear rather than build something to drive a planet and
2.85 seems good enough. But as I read through this I can see a
definite advantage to building the 3.17, less weight and more
horsepower for free. However I am having a problem with the
connection of the planet flange and the prop shaft. If I am seeing
the drawings and understanding correctly, there will be eight or ten
.25 small screws going through the flange and into the end of the
shaft with a .190 wall. This doesn't make any sense to me. Is there
something welded to the .190 shaft to accept the .25 screws? If the
shaft were .250 and tiny #2 machine screws were used there would be
enough meat in the end of the shaft to drill and tap but would that
be strong enough? I must be missing something or I am not
understanding it correctly. Also how long should the prop shaft be?
On Tracy's website he says that a longer shaft is better. What is the
length of the Ross and Tracy shaft? Paul Shamlian
We edm holes in the planet carrier planet shafts. This saves the hard
smooth bearing surface for the needles bearings. The existing planet
shafts are VERY hard to get out with out destroying the planet
carrier.
As I recall the holes are at least 7/16th in dia.. The bolts going
through these six holes attach the planet carrier to the aft flange
on the hollow prop shaft. The aft flange is either tig welded on
the hollow prop shaft or it is bolted on with a dozen or more 10-32
screws. Ross tig welded it on. It is then wise to normalize and re
heat treat to at least Rockwell 60. The loads on the rear flange,
unlike the front front prop flange, are pure shear loads. Then the
shaft should be ground for the main needle bearings. The reason the
prop shaft is so long is to react the gyro bending loads from the
prop when the A/C spins or stalls.
Paul Lamar
Paul. How would chromoly go for the prop shaft ?? What are the
planetary gears that Tracy uses? Neil.
Chrome molly tubing would be great. The same ones I just delivered to
Chris in NZ. :) Is your gear box giving trouble?
It is a Ford truck auto transmission rear set.
I can get them for under $200. I'll know more about shipping cost
tomorrow. Today was a holiday for the PO. I do know UPS and FedX is
very very expensive. I think Parcel Post will be the best bet. I will
also try DHL.
Paul Lamar
Paul, Valuable info as usual. No my g/box is fine, but am just
nervous with Tracy being retired. Have a gap with not much in front
of me so looking at making a complete g/box as a trial, which will
give exact measurements. The alloy housing can be cast in China as
have found a bloke here in OZ that is getting a lot of work done in
china, so eliminates the research in finding someone to do a casting
rather than cutting the whole thing out of solid. All day dreams at
the moment, but currently working on suppliers. Neil.
Not to worry they are not that hard to make. Do you have a place in
Parkes with a lathe about this size? This is Chris Hoskins lathe in
NZ and he is building a Ford based Gbox.
Paul Lamar
Other early GMs used that torque tube style driveshaft. A friend had a
'64 Olds with one. (Like Al from Al's Toy Barn drove in Toy Story 2). He
scraped the car when the joint wore out. Finding one of those or a rear
end that has one will be a bit of a barn find.
Ken Cohagen