Subject: Mad Mike & his 4 rotor Rx7 Win again!!
From: rotaryeng
Date: 1/25/2014, 9:49 AM
To: AAA-rotaryeng


http://www.youtube.com/watch?v=zMzt34_zOyE

   Enjoy!

-Dan G.

Some times I think the customers understand and appreciate the rotary
better than Mazda Corp. :)

Paul Lamar



I couldn't agree more! Mad Mike is one of the world's great
Mazda/Rotary Champions, saw an interview awhile back in which he
stated he'd owned 27+ rotary powered vehicles over the years! He
keeps another 4 rotor Rx-7 in Japan, called the JAPBUL. (the one in
the linked video is the MADBUL) He also has a Turbo 3 rotor (812hp
20B) Rx-8 "BADBUL" (which I've seen IRL). I don't understand why
Mazda doesn't flaunt his and other success like his by others, major
fumble on their part.

http://www.madmike.co.nz/

-Dan G.


Rotaries most great benefit is easily stackable. I think if we use
better material for shaft.10 or more rotor can be stacked and still
its very small and by just common sense if we use ceramic or inconel
it can be air cooling engine. Efficiency easily go over current
gasoline engine

I think about crowed funding at kick starter or indiegogo for making
this. I have no intend about get money from it just fun job. So
people may interest in.

As we know 12 rotor rotaries size is 1.5m and it will produce over
2000hp easily. Apache choppers engine just produce 1700 hp but
extremely expensive. If we success I think we can supply this engine
on many aircraft and marine solution

What do you think about it paul and fellows?

P bear

IMHO 5 rotors in line is the limit.

Paul Lamar




As Paul said 5 rotors are likely max stack practical. Size and
weight start to be a problem especially for mobile use. It would be
more efficient to make larger radius and eccentricity with 70 or 80mm
rotor width. A 5 rotor engine with a firing order of 1-5-2-4-3 would
not require large balance weights. An inline 6 has 1 and six at TDC
at the same time.2and 5, and 3 and 4 also run together. the engine is
basically balanced and runs smoothly. A V12 is basically two I6
engines combined so is even smoother. A 5 rotor fires like a V10 so
should run very smooth along with strong torque. 80mm width would
allow doubling the spark plugs or installing dual injectors in
precombustion chambers with glow plugs to get the diesel or Jet fuel
to ignite. With Paul´s ignition or the new diesel injectors that fire
up to 7 or 8 times per cylinder firing could produce excellent BSFC.
Depending on the eccentricity and radius dimensions chosen, 1,000 to
1,500HP is possible with lower fuel burn than a turbine with
equivalent TBO´s. Fuel burn at the same power levels could be 50% to
75% of the turbine with turbo normalize and power recovery. Inconel
or TiAl turbine housings to reduce weight could solve the installed
weight issues. The slightly higher installed weight would be offset
be lower fuel tank fill due to the reduced fuel burn rate.

Dale Davies



Hi.

My aim is how to make prototype cheap as possible. I just want to show to or make sure that rotary engine is enough for high price commercial use. for that It must under minimum modification from current Mazda engine.

And I can't agree with Paul's opinion,  Is anyone know Mazda's 4 rotor's engine's shaft's material? If I know what it is. what kind of material can handle with 8 or 10 or more rotor with current design itself.

Making new rotor is huge change I think it will be extremely high cost. we must remake seal, rotor and housing. so on.

but Shaft is differ, If we can keep current shape. we can use any other parts as possible. we can (or I  can) save time and effort.

and If still shaft cause problem. luckily we can wide shaft diameter easily.

IF any one tell me about Mazda's 4 rotor' shaft's material I really appreciate it.

Thank you

P_Bear --

Mazda engineers would be rather stupid if they did not use the finest materials when building
engines to win LeMans. Cost was no object.

http://www.rotaryeng.net/material-tech.pdf <http://www.rotaryeng.net/material-tech.pdf>

http://www.rotaryeng.net/Mazda_R26B_US.pdf <http://www.rotaryeng.net/Mazda_R26B_US.pdf>


Paul Lamar

There have been other rotary engines manufactured. Some of these
have been of large displacement for industrial applications.
Mazda produced one engine for a domestic front engine car.  Very
rare.  It had a larger eccentricity and radius and the in
development 16X is similar.

The design seems to need a 7:1 radius/eccentricity ratio to
work.  With larger dimensions the main bearing diameter is
increased allowing more torque to be transmitted.  Some of the
CW?  military engines were 5 rotor heavy fuel engines so it can
be done.

If you keep to the 70mm or 80mm rotor width, the Mazda style
seals can be used saving developing them.  Other than Mazda,
NSU, Citroen and the Russian VAS engines, it is difficult to get
information on the engine dimensions and other design
information.  Machining of the rotor for the required curve to
follow the trochoid shape and the rotor housing trochoid are the
biggest problems to overcome as I see.

Getting larger timing gears engineered and built is a minor
problem that also would need to be addressed.  The Mazda 26B for
the Le Mans race car had stiffener parts added to control
bending loads, and that on just 4 rotors.  Imagine the bending
stress on 10 or 12 rotor stack.  It would be easier to redo the
rotor dimensions to get the displacement and thus power than to
try stacking more rotors.  Difficult, yes; impossible, hack no!


Dale Davies


Dale get yourself a copy of "The Wankel
RC Engine Design and Performance" by R.F.Ansdale Published by A.S.
Barnes & Company Lib of Cong 69-18692

Lots of good theoretical design stuff.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net.
You Tube http://tinyurl.com/beqqxas.
Copyright 1998-2013 All world wide rights reserved.