Subject: New 3 rotor helicopter design
From: rotaryeng
Date: 2/19/2014, 3:29 PM
To: AAA-rotaryeng


       Hi all,

       Hope you like the photo this is about the shape I want to put into my
         helicopter

       I have drawings(incomplete) of the Scorpion Too rotor hub and swash
       plate should anyone want a copy please PM me and I will send.

       I am working on engineering drawings of the Rotorway 162F which is a
         much improved system.

       The system from the controls up is less complex also working on
       drawings of double reduction gearbox.

       While I think the worm and wheel may be good it doesn't work with a
       vertical engine and gets away from my original intention.

       It would put the engine off center. But would be good where the twin
         engine would be used, the question would be how much torque will it
         withstand.

       I had a look at a D2 Helicopter the other day, I am told that this
       beast cost a fortune to build the gearbox designed by local engineer
       is 18KG (40Lbs) and using a diesel 2stroke engine and the guy asked
       why I was using a rotary I believe with the fully articulated rotor
       head it just about shook its self to piece and lifted the right skid
       off the ground.

       I think I could fix this with a three rotor rotary engine plenty of
       power a good balance( hang it up on a crane) , two blades or 3 fixed
         blades and probably with the 18KG gearbox in situ the cabin is built
         very strongly, just needs the power to lift it, their diesel only
       came in at 190hp. My Scorp rotary turbo  will be 500hp and is a lot
       lighter, for a full grown helicopter the D2 would be good.

       Regards George  Crooks Aus

       I would like the dwgs.

       You don't want to mount the rotary engine vertically.

       The essential cooling oil drain back from the rotors would not work.
       It should be mounted horizontal and upright as it is in a car.

       You can get away with it in a piston engine but not in a rotary.


       That is another  advantage of the worm drive. It turns the rotary
       motion 90 degrees. You can mount the single engine at a slight angle
       looking down on it to adjust the CG.  Power for the tail rotor can
       come back from a shaft under the engine.


       Paul Lamar



       Please ensure that your worm drive can tolerate the expected torque, one of my early gearbox failures was a worm drive that looked substantial, but the worm flexed and jumped over the teeth on the worm wheel. Obviously the length and stiffness of the worm are of great importance if it is to handle much torque. A suitable gearbox may be quite massive.

       John Evans


       Of course :)

       Make sure the pinion shaft is of sufficient diameter as the stiffness goes
       up with the cube of the diameter and the pinion is supported on both
       ends with bearings. Use oil pressure fed plain bearings to keep the weight
       down and handle the RPM of a rotary.  The rotor shaft can use needle bearings
       as the RPM is low.

       Paul Lamar



   Two planetary gear set in series, each about 4.5:1 ratio, or the high speed 5:1 and the low speed 4:1 to get to 20:1 might be simpler, smaller and with better efficiency. Just my 2 cents.

   Rolf Pfeiffer

   That is fine but where do you get them and what do they cost?
   The Ford is not strong enough for 4,000 foot pounds of rotor torque.

   Paul Lamar


That is of course true. It would have to be a custom build unit and then the cost is prohibitive.

The layout and design is not too hard to do but getting the gears cut is expensive, unless production gears from a gear manufacturer can be found which is not easy and not likely to be found.

Enough $ will buy a ready and suitable unit from a gear company.

Big toys cost big money.

Rolf Pfeiffer


A worm drive is much cheaper.

Paul Lamar

   --

    The Rotary Engine News Letter. Powered by Linux.
    ACRE NL web site. http://www.rotaryeng.net
    You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2014 All world wide rights reserved.