Subject: Re: AW: AW: AW: AW: PRIVATE update
From: rotaryeng
Date: 6/1/2014, 8:45 AM
To: Poul Henrik Woelfle
CC: AA-robin Lamar <robin.lamar@earthlink.net>

Yes there are just two Mazda front e-shaft pulley hubs.
The 5 mm equal spaced six bolt racing  version and the 6mm four
bolt version unequally spaced version. Used on stock everything including
the 3 rotor. One hole is 5 degrees off for indexing the timing marks.

Yes the current sensor of choice is purely optical.

The hall effect version did not work. All the multiple magnet fields combined
into one large field :) Keep this under your hat as well.
We don't want to make it too easy for our competitors :)

I am at Home so I don't have the dwg iges but will send it soon.
Keep this under your hat as we are thinking about
a patent for just the trigger mech. It has advantages for precise
angular shaft measurements. As the sensor is always held concentric
regardless of how the shaft may move around.

  P

On 06/01/2014 06:59 AM, Poul Henrik Woelfle wrote:
Hi Paul,

thank you for the file. Are the 6 holes and bolts with spacers to get the arrangement away from the e-shaft on a Mazda engine? If so we can replace the current PVL Fire ignition with yours and we will have enough space to fit it directly on the shaft. Then we can have the adjustable housing located in a mounting plate (that normally retains the PVL stator and keeps it concentric to the shaft) and run it without the bearing.

When you have a file of the housing please send it. If my above assumption is correct I can modify it to fit our engine.

By the way, just to confirm: The sensor is purely optical, so material and thickness does not matter, correct? Would we help the sensor if we make the holes rectangular? Then we could just make a small hub and have the trigger disc from something light and easy to cut and have it laser/water cut.

Many thanks,

Poul Henrik Woelfle
  Woelfle Engineering GmbH
Randstraße 109 • D - 47804 Krefeld • Germany
Tel +49 2151 151020 • Fax +49 2151 151019
www.woelfle-engineering.com
HRB 7369, Amtsgericht Krefeld • Director / Geschäftsführer: Paul A. Woelfle

-----Ursprüngliche Nachricht-----
Von: rotaryeng [mailto:rotaryeng@earthlink.net]
Gesendet: Samstag, 31. Mai 2014 14:30
An: Poul Henrik Woelfle
Betreff: Re: AW: AW: AW: PRIVATE update

Here is a 3d and an IGES of the trigger disc.

You need to fasten the trigger disc to the end of the e-shaft and the stationary sensor housing locates  off that with a ball bearing.

Paul


On 05/30/2014 07:19 AM, Poul Henrik Woelfle wrote:
Sounds good. When you initially mentioned the optical trigger for the EFI or so some time back, I thought you might end up this route anyway. Since it's optical you probably just want to make sure it runs in a clean environment. We don't have much room, but will find some space once we see the bits, so no need to machine parts. If you have 3D CAD files of the necessary bits feel free to send them in STEP, IGES or SolidWorks.

Best Regards,

Poul Henrik Woelfle
   Woelfle Engineering GmbH
Randstraße 109 • D - 47804 Krefeld • Germany Tel +49 2151 151020 • Fax
+49 2151 151019 www.woelfle-engineering.com HRB 7369, Amtsgericht
Krefeld • Director / Geschäftsführer: Paul A. Woelfle

-----Ursprüngliche Nachricht-----
Von: rotaryeng [mailto:rotaryeng@earthlink.net]
Gesendet: Dienstag, 27. Mai 2014 18:26
An: Poul Henrik Woelfle
Cc: Kornder Helmut <""Kornder Helmut ">,AA-robin Lamar
<robin.lamar@earthlink.net>
Betreff: Re: AW: AW: PRIVATE update

We have done away with the sprocket trigger.

It was not fast enough over 8000 RPM

we now have a high speed optical trigger that can trigger in 10 nano
sec one one thousands of a micro sec which is one millionths of a
second :)

If you have a flywheel we need six holes 1/4 inch in diameter spaced 10 degrees apart starting at firing time.

If you don't have a flywheel send me a dwg of the nose of the e-shaft and I will machine a device that will do the job.

No need for a bracket to hold the pickup on the engine as this device will be self contained and stationary. There is a thin disk inside that rotates.
There is a
small external timing adjusting link with 6-32 rod ends.

Paul

On 05/27/2014 04:53 AM, Poul Henrik Woelfle wrote:
Hey Paul,

No worries, the oil bearings will be on the new OCR design. You can't reasonably fit them on the 294 as the geometry does not allow for the extra seals. There is a good market for a light CCR even if it has less power, so it is a good starting point for us :).

Best Regards,

Poul Henrik Woelfle
    Woelfle Engineering GmbH
Randstraße 109 • D - 47804 Krefeld • Germany Tel +49 2151 151020 •
Fax
+49 2151 151019 www.woelfle-engineering.com HRB 7369, Amtsgericht
Krefeld • Director / Geschäftsführer: Paul A. Woelfle

-----Ursprüngliche Nachricht-----
Von: rotaryeng [mailto:rotaryeng@earthlink.net]
Gesendet: Dienstag, 27. Mai 2014 01:21
An: Poul Henrik Woelfle
Betreff: Re: AW: PRIVATE update

When are you going to install oil pressure fed rotor bearings? :) Max RPM will go up several thousand and the HP will increase greatly.

Plus you can run the engine full power indefinitely.

Those of us with Mazda's don't know what you Europeans  see in roller
rotor bearings :)

Cheaper two.

All those tiny needles are turning a zillion RPM.
Makes no rhyme or reason.

Needle bearings hate RPM  :)

Paul

On 05/26/2014 01:42 PM, Poul Henrik Woelfle wrote:
Hi Paul,

Too bad, but another reason to return soon ;)

The ceramic seals were/are all OK. Main issue is customers using too
long spark plugs instead of those required in the manual...
Just the ceramic needles in the bearing didn't like any dust or
debris. That would make them crack, and once the first cracked they
all went into powder, and the rotor crashed into the housing.

Fingers crossed for the weekend :)

Best Regards,

Poul Henrik Woelfle
     Woelfle Engineering GmbH
Randstraße 109 • D - 47804 Krefeld • Germany Tel +49 2151 151020 •
Fax
+49 2151 151019 www.woelfle-engineering.com HRB 7369, Amtsgericht
Krefeld • Director / Geschäftsführer: Paul A. Woelfle

-----Ursprüngliche Nachricht-----
Von: rotaryeng [mailto:rotaryeng@earthlink.net]
Gesendet: Sonntag, 25. Mai 2014 17:58
An: Poul Henrik Woelfle
Betreff: Re: PRIVATE update

Big Mistake. We live at the beach with a guest room :)

BTW what brand of ceramic seal broke into powder and ruined the engine?

We are testing the ignition next week end at Sebring Fla on an RX7 race car.
I'll let you know how it goes.

Paul

On 05/25/2014 02:59 AM, Poul Henrik Woelfle wrote:
Hi Paul,

I hope all is well. We had an awesome trip to the US. I had hoped
to drive by and visit you, but we only had a half day left and
hadn’t seen any of LA yet, so we went for the traffic jam ;-).
Hopefully I will have some good reasons to come again rather sooner
than later
:-)

Since my return things have been terribly busy, but with some good
results in between. In a couple of weeks we will be ready to test
your ignition. Our customer in the UK is currently too busy with
other stuff, but we should have our own testing options ready by
then. If you have a unit for testing please let me know.

Best Regards,

Poul Henrik Woelfle

*Woelfle Engineering GmbH*

Randstraße 109 • D - 47804 Krefeld • Germany

Tel +49 2151 151020 • Fax +49 2151 151019

*www.woelfle-engineering.com
<http://www.woelfle-engineering.com/>***

HRB 7369, Amtsgericht Krefeld • Director / Geschäftsführer: Paul A.
Woelfle






-- 

 The Rotary Engine News Letter. Powered by Linux.
 ACRE NL web site. http://www.rotaryeng.net
 You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2014 All world wide rights reserved.