Subject: Article on the development of OMC Snowmobile RCEs
From: rotaryeng
Date: 6/17/2014, 7:30 AM
To: AA-1-Me




   Hallo: by serendipity, 'chiripa' in Spanish, I've found these comments by one of the engineers who were involved in the development of OMC Wankel engines.
   Hope it's of some interest to you. Have a good season. Best regards.

   Salut       Jose Gros-Aymerich; Madrid, Spain

   http://vintageomc.webs.com/theomcproduction.htm <http://vintageomc.webs.com/theomcproduction.htm>

   "Max Bentle of Curtis Wright is credited with the kinematic inversion of the engine allowing the housing to remain stationary with a rotating crankshaft."

   Untrue. It was a person at NSU. The name later.

   "The pressurized oil system allowed the use of conventional babit bearings and with the addition of an oil cooler to maintained internal temperatures adequately."

    Are you listening you Wankel heads in Europe? :)

   "Curtis had use “D-Gun” tungsten carbide from Linde as their coating, which was very effective, but extremely expensive."

   Interesting.

   "It was also hundreds of pounds lighter than the V-8 being used and as such would out accelerate them even with 100 less hp."

   "Both versions meet the design requirement of 100 hrs @ WOT."


   "The trochoid coating was still “D-Gun”, as research hadn’t developed a lower cost suitable coating yet."

   "After several months of work, it became apparent an oil-cooled engine could not be made cost competitive with a 2 cycle and work on oil cooled engines stopped."


   " Unlike a piston engine, the rotor is a captive heat source with very little heat rejected to the housing walls. As such most of the cooling had to come from the incoming charge to cool the rotor. The result is a significant reduction in volumetric efficiency, the actual amount of air going thru the engine vs its theoretical capacity. This is due to the significant heating of the charge as it passes thru the engine."

   "Unfortunately he had designed a 2 stage axial blower running at 30,000 RPM and took 35 hp to drive to cool the CW design."


   "We knew an axial fan could not generate sufficient pressure that would result in the velocity required to cool the engine."


   "The rotor bearing was the weak link of this engine. Being inside the rotor, it is completely dependent on the incoming charge for cooling and lubrication. The bearing was already pretty special. It had a silver plated retainer and a high temperature temper of the outer race. Steel grows; get larger, as it gets hotter. That is until it exceeds the temper temperature where in it gets smaller. As I figured out after 100’s of tests, there was a lubrication breakdown between the retainer and the outer race. The result was steel running on steel at very high speeds generating extreme heat. The result was the bearing shrinking onto the crank eccentric stalling the engine. It took a hydraulic press or a sledge hammer' to get them apart. I took several samples to SKF Research and talked to the chief metallurgist. He told me this was impossible to do. When I suggested he come to Waukegan and see for himself, he said the bearing had to be reaching 1800 F for this to happen. This type failure was self-destructing. When the bearing got near its thermal breakdown temperature it would self generate additional heat causing further oil breakdown, causing additional heat, etc, etc,etc. "

   The European Wankel builders have yet to learn a lot of these lessons.
   Not Mazda. Mazda is the gold of the Wankel world.

   Paul Lamar



Kinematic inversion.
The Gentleman at NSU was Mr. H, D, Paschke, Hans Dieter.

http://www.der-wankelmotor.de/Wankelmotor/wankelmotor.html

Rolf Pfeiffer

How do we get that in English Rolf?

Paul Lamar

   The Rotary Engine News Letter. Powered by Linux.
    ACRE NL web site. http://www.rotaryeng.net
    You Tube http://tinyurl.com/beqqxas
    Copyright 1998-2014 All world wide rights reserved.