Subject: Article on the development of OMC Snowmobile RCEs
From: rotaryeng
Date: 6/17/2014, 11:20 AM
To: AA-1-Me


Hallo: by serendipity, 'chiripa' in Spanish, I've found these
   comments by one of the engineers who were involved in the development of
   OMC Wankel engines.
Hope it's of some interest to you. Have a good season. Best regards.

Salut      Jose Gros-Aymerich; Madrid, Spain

http://vintageomc.webs.com/theomcproduction.htm <http://vintageomc.webs.com/theomcproduction.htm>
   <http://vintageomc.webs.com/theomcproduction.htm>

"Max Bentle of Curtis Wright is credited with the kinematic
   inversion of the engine allowing the housing to remain stationary with a
   rotating crankshaft."

Untrue. It was a person at NSU. The name later.

"The pressurized oil system allowed the use of conventional babit
   bearings and with the addition of an oil cooler to maintained internal
   temperatures adequately."

 Are you listening you Wankel heads in Europe? :)

"Curtis had use “D-Gun” tungsten carbide from Linde as their
   coating, which was very effective, but extremely expensive."

Interesting.

"It was also hundreds of pounds lighter than the V-8 being used and
   as such would out accelerate them even with 100 less hp."

"Both versions meet the design requirement of 100 hrs @ WOT."


"The trochoid coating was still “D-Gun”, as research hadn’t
   developed a lower cost suitable coating yet."

"After several months of work, it became apparent an oil-cooled
   engine could not be made cost competitive with a 2 cycle and work on oil
   cooled engines stopped."


" Unlike a piston engine, the rotor is a captive heat source with
   very little heat rejected to the housing walls. As such most of the
   cooling had to come from the incoming charge to cool the rotor. The
   result is a significant reduction in volumetric efficiency, the actual
   amount of air going thru the engine vs its theoretical capacity. This is
   due to the significant heating of the charge as it passes thru the engine."

"Unfortunately he had designed a 2 stage axial blower running at
   30,000 RPM and took 35 hp to drive to cool the CW design."


"We knew an axial fan could not generate sufficient pressure that
   would result in the velocity required to cool the engine."


"The rotor bearing was the weak link of this engine. Being inside
   the rotor, it is completely dependent on the incoming charge for cooling
   and lubrication. The bearing was already pretty special. It had a silver
   plated retainer and a high temperature temper of the outer race. Steel
   grows; get larger, as it gets hotter. That is until it exceeds the
   temper temperature where in it gets smaller. As I figured out after
   100’s of tests, there was a lubrication breakdown between the retainer
   and the outer race. The result was steel running on steel at very high
   speeds generating extreme heat. The result was the bearing shrinking
   onto the crank eccentric stalling the engine. It took a hydraulic press
   or a sledge hammer' to get them apart. I took several samples to SKF
   Research and talked to the chief metallurgist. He told me this was
   impossible to do. When I suggested he come to Waukegan and see for
   himself, he said the bearing had to be reaching 1800 F for this to
   happen. This type failure was self-destructing. When the bearing got
   near its thermal breakdown temperature it would self generate additional
   heat causing further oil breakdown, causing additional heat, etc, etc,etc. "

The European Wankel builders have yet to learn a lot of these lessons.
Not Mazda. Mazda is the gold of the Wankel world.

Paul Lamar



   Kinematic inversion.
   The Gentleman at NSU was Mr. H, D, Paschke, Hans Dieter.

   http://www.der-wankelmotor.de/Wankelmotor/wankelmotor.html

   Rolf Pfeiffer

   How do we get that in English Rolf?

   Paul Lamar

From Google translate:

https://translate.google.com/translate?sl=auto&tl=en&js=y&prev=_t&hl=en&ie=UTF-8&u=http%3A%2F%2Fwww.der-wankelmotor.de%2Findex.html&edit-text=&act=url

Sam Chitwood
The Rotary Engine News Letter. Powered by Linux.
 ACRE NL web site. http://www.rotaryeng.net <http://www.rotaryeng.net/>
 You Tube http://tinyurl.com/beqqxas
 Copyright 1998-2014 All world wide rights reserved.