Subject: Article on the development of OMC Snowmobile RCEs
From: rotaryeng
Date: 6/19/2014, 5:22 AM
To: AA-1-Me




Hallo: by serendipity, 'chiripa' in Spanish, I've found these comments by one of the engineers who were involved in the development of OMC Wankel engines.
Hope it's of some interest to you. Have a good season. Best regards.

Salut       Jose Gros-Aymerich; Madrid, Spain

http://vintageomc.webs.com/theomcproduction.htm <http://vintageomc.webs.com/theomcproduction.htm>

"Max Bentle of Curtis Wright is credited with the kinematic inversion of the engine allowing the housing to remain stationary with a rotating crankshaft."

Untrue. It was a person at NSU. The name later.

"The pressurized oil system allowed the use of conventional babit bearings and with the addition of an oil cooler to maintained internal temperatures adequately."

Are you listening you Wankel heads in Europe? :)

"Curtis had use “D-Gun” tungsten carbide from Linde as their coating, which was very effective, but extremely expensive."

Interesting.

"It was also hundreds of pounds lighter than the V-8 being used and as such would out accelerate them even with 100 less hp."

"Both versions meet the design requirement of 100 hrs @ WOT."


"The trochoid coating was still “D-Gun”, as research hadn’t developed a lower cost suitable coating yet."

"After several months of work, it became apparent an oil-cooled engine could not be made cost competitive with a 2 cycle and work on oil cooled engines stopped."


" Unlike a piston engine, the rotor is a captive heat source with very little heat rejected to the housing walls. As such most of the cooling had to come from the incoming charge to cool the rotor. The result is a significant reduction in volumetric efficiency, the actual amount of air going thru the engine vs its theoretical capacity. This is due to the significant heating of the charge as it passes thru the engine."

"Unfortunately he had designed a 2 stage axial blower running at 30,000 RPM and took 35 hp to drive to cool the CW design."


"We knew an axial fan could not generate sufficient pressure that would result in the velocity required to cool the engine."


"The rotor bearing was the weak link of this engine. Being inside the rotor, it is completely dependent on the incoming charge for cooling and lubrication. The bearing was already pretty special. It had a silver plated retainer and a high temperature temper of the outer race. Steel grows; get larger, as it gets hotter. That is until it exceeds the temper temperature where in it gets smaller. As I figured out after 100’s of tests, there was a lubrication breakdown between the retainer and the outer race. The result was steel running on steel at very high speeds generating extreme heat. The result was the bearing shrinking onto the crank eccentric stalling the engine. It took a hydraulic press or a sledge hammer' to get them apart. I took several samples to SKF Research and talked to the chief metallurgist. He told me this was impossible to do. When I suggested he come to Waukegan and see for himself, he said the bearing had to be reaching 1800 F for this to happen. This type failure was self-destructing. When the bearing got near its thermal breakdown temperature it would self generate additional heat causing further oil breakdown, causing additional heat, etc, etc,etc. "

The European Wankel builders have yet to learn a lot of these lessons.
Not Mazda. Mazda is the gold of the Wankel world.

Paul Lamar


   Kinematic inversion.
   The Gentleman at NSU was Mr. H, D, Paschke, Hans Dieter.

   http://www.der-wankelmotor.de/Wankelmotor/wankelmotor.html

   Rolf Pfeiffer



Hello Paul,


Here is a translation. The two moving pictures of DKM and KKM fit above and besides the name H.D. Paschke.



Felix was just 25 when he wrote this in his diary:

“The huge difference between the efforts by BBC (no reference is cited) and my own is that I do not want to replace steam or a water jet with a jet ignited gas, but I would like to make use of the same power generation by the gas expansion as it occurs in the reciprocating engine, however in rotating motion. Intake, compression, power and exhaust shall remain as is since I trust that ignition and expansion of gasoline etc. is best suited for power generation. Only the mechanical volume variation is to be achieved under full rotation instead of a reciprocating motion. This is my task.”

From this entree in his diary to the first working Wankel engine, the DKM 54, was a long and thorny road ahead.



It was Feb. 1, 1957 when the DKM 54 first came to life on a test bed. After some adjustments of ignition timing and gas mixture its running became smooth. For the external rotor and for the internal rotor only pure rotation exists where the inner rotor solely functions as valve to control intake and exhaust. With this running engine the possibility of a working rotary engine was confirmed. For practical applications this form of engine was unsuitable, e.g. the spark plugs were located in the pockets of the inner rotor.



It was H.D. Paschke of NSU who succeeded in achieving the kinematic inversion from the DKM to the KKM (DKM = Drehkolbenmotor, Dreh= Rotation, KKM = Kreiskolbenmotor, Kreis = circle, where the centre of the inner rotor describes a circle and the outer rotor becomes stationary.)

Mr. Paschke worked under strict secrecy to make the outer rotor stationary.

Now there was no longer pure rotation, but two rotations superimposed on each other. Negative accelerations occur on the short axis pointing to the inside. Problems arise to remove the cooling oil from the rotor as it churns with loss of energy inside the rotor just moving back and forth. Felix Wankel snubs the idea as he becomes aware of it, however it is too late when he grudgingly makes that famous statement: “You made a plow horse out of my race horse.”  To which he was told: “I only wish we already had the plow horse.”



Now the problems with the KKM begin to appear. Chatter marks occur. At times it is only a so called chatter shadow. Chrome coatings of the housings flake off and the engine die off in short order. At Mazda it is being recognized that the weight of the apex seals is to blame. Bores are drilled through the cast iron seals thereby finally reached long duration runs. In first production models NSU and Mazda use coal-graphite seals. NSU applied carbon-antimony, Mazda carbon-aluminum materials. Mazda advanced the seal technology to later to return to cast iron seals and chrome coating in the housing. A steel insert is added to the Al housing with precision chrome plating where the chrome layer is so thin that no grinding is required and high durability is still obtained. The cast iron seals were later replaced by ferrous seal. During the oil crisis in the 1970’s more and more licensees leave the scene. Only Mazda as the only car manufacturer remains faithful. As Audi-NSU stopped production of the RO80 in 1977 production of the Wankel as car engine ends in Germany.



With the development of the Renesis Wankel engine in the RX8 a ‘race horse’ engine was yet achieved from the ‘plow horse’. The present version (I am not sure when it was written) the Renesis delivers 231 hp at 8500 rpm. The Renesis RX8 apparently requires 50% less lubricating oil and 40% less fuel than its predecessor.  Besides that it meets the Euro-4 emission regulations. The side exhaust port was only possible with a ceramic insert cast into the housing. The housing running surface is now of a chrome-molybdenum alloy. Molybdenum is one of the few materials where chatter marks do not occur and it has excellent running properties.


Rolf

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.