Subject: high speed CD ignition with air injection.
From: rotaryeng
Date: 6/21/2014, 11:01 PM
To: AA-1-Me



   If you firing a rotary engine six times every 10 degrees at 10,000
   RPM you need a fast crank angle sensor.

   This ignition system has the promise of reducing the fuel consumption,

   increasing the power, reducing hydro carbon emissions and curing an
   occasional mis-fire at idle due to port overlap. It is six times more likely
   to fire a bad mixture.


   Paul Lamar

   Ignition of gasoline depends on the spark being immersed in a mixture
   in the air fuel range of 10:1 to 20:1. The mixture ratio varies
   widely in the combustion chamber and it is very turbulent meaning
   that any given moment the mixture may or may not not be ignitable.
   Due to port overlap some exhaust gases (less oxygen) could be
   included making the mixture non ignitable at a given moment in time
   causing a miss.


   That is what happens in the old Mazda 13B and causes a distinctive
   and noticeable miss at idle. The RX8 eliminated the port overlap for
   that reason.

   This ignition is six times more likely to find an ignitable mixture
   ratio because it waits for a good mixture to come along :) Notice the
   Wankel combustion stroke lasts almost 300 degrees while the piston
   combustion stroke is only about 120 degrees. During this long time
   period some un-combusted combustible mixture may be passing the spark
   plug.

   We know this to be a fact because of the high hydro carbon content in
   the Wankel exhaust. Our goal is to ignite that mixture thereby
   gaining a lower BSFC number and more power.


   Paul Lamar

   I just had another idea along these lines. If the mixture is too rich
   to ignite a very small quantity of high pressure fresh air injected
   close to the spark around TDC would help. The amount and duration
   could be determined by experiment. Here are some 3D's. NOS or
   hydrogen  could also be used but air is cheaper :)

   Paul Lamar

   A very good idea, this new approach to Stratified Charge RCEs! Now
   that electronics, EFI and electromechanical devices have prices
   lower that going out for dinner, the number of ways for improving
   all issues formerly problematic in Wankel engines grows
   exponentially year after year. Please keep us aware of results!

   Best regards. Salut â          Jose Gros-Aymerich; Madrid,Spain

   Hi, the Orbital Fuel injection uses dual injectors: one to meter the
   fuel and another for the compressed air blast to inject it into the
   cylinder. Mercury Optimax outboards are one application. Originally
   designed for two strokes, it works great on four strokes. I do not
   know if it has been tried on a rotary.  It should work. They seem to
   like to have the spark plug electrodes out in the edges of the
   fuel/air plume.  That could be a problem with the rotary.  It is
   more expensive than single fluid injection.


   Murry I. Rozansky

   The difference is the quantity of high pressure air. Small quantity
   low compressor HP consumption. We need just enough to ignite the rich
   mixture around the spark gap only.

   Paul Lamar


   Paul and Jose,
   Because you are looking for the lowest BSFC you would want a lean
   mixture and then add richness only at the plug.... making it a
   stratified charge.

   Also if you want to increase the burn rate (we do),  you could use lower
   pressure air to make an "air curtain" between the exhaust port and your
   peripheral intake,  segregating the cycles.

   Barry Bordes


   It takes HP to compress and pump air. That HP comes out of the bottom line
   on the overall fuel burn. One would want to limit that. We just need a
   few molecules of fresh air in the spark plug gap to fire the occasional
   rich mixture.

   Paul Lamar

   Here is some relatively recent work on this subject.

   From :

   CFD INVESTIGATIONS OF MIXTURE FORMATION, FLOW AND COMBUSTION
   FOR MULTI-FUEL ROTARY ENGINE


   Von der Fakultät für Maschinenbau, Elektrotechnik and Wirtschafts-
   Ingenieurwesen der Brandenburgischen Technischen Universität Cottbus
   zur Erlangung des akademischen Grades eines
   Doktor-Ingenieurs (Dr.-Ing.)
   genehmigte Dissertation
   vorgelegt von
   Master of Science
   Husni Taher Izweik
   Geboren am 15.12.1954 in Zawia, Libyen
   Vorsitzender: Prof. Dr.-Ing. P. Steinberg
   Gutachter: Prof. Dr.-Ing. H.P. Berg
   Gutachter: Prof. Dr. E. Sigmund
   Tag der mündlichen Prüfung:
   18.11.2009

   Please the above part needs a little human translation Rolf.
   Also Rolf do you have any email addresses at Wankel Supertec?
   They should be interested in testing my ignition.
   I know you have been over there.

   " In
   Wankel engine it is important to use ignition assistant when the engine prepared to run on
   diesel fuel due to lower compression ratio and hence chamber temperature. The idea is to run
   the engine in lean concentration overall, but locally rich combustion. So, it is necessary to
   reach the ignitable charge, (0.6% - 7.5% by volume, diesel vapor) at the spark plug.

   The study in this part was concentrated on the diesel mixture formation inside the
   combustion chamber of Wankel engine and the main conclusion can be summarized as
   follows.

   Injector angle between holes below 13 deg is too small and the spray cones interfaced and
   acts like one bore nozzle. 18 deg angle between injector holes show better penetration
   and covers most of the combustion chamber at spray angle of 32 deg.

   Early fuel spray (39 deg BTDC) gives more time for mixture formation, but the fuel
   concentration at the spark is lowered due to charge forward movement, when ignition
   time is on, (10 deg -15 deg BTDC). 29 deg BTDC spray start angle gives better results for
   engine speed less than 4000-rpm.

   The new suggested spark plug position (18mm from short axis) shows ignition
   difficulties due to low fuel concentration on this position, as the fuel evaporation rate
   is low near the nozzle.

   The new suggested injector position (31mm before short axis), shows better results
   and covers more area of combustion chamber, and shows more fuel penetration at
   spray angle 40 deg."

   End of quote.

   Historically with stratified charge it has been a challenge to get the right mixture
   in the right place at the right time.

   This is where my multi spark on demand ignition system could help greatly.


   Paul Lamar




Paul,

You can contact Wankelsupertec at this address: info@wankelsupertec.de <mailto:info@wankelsupertec.de

It would be a breach of trust to publish the Email address of Prof. Dr. Ernst Sigmund, but I'll send it to you only in a private Email.

Yes, I have spent the better part of a day in Cottbus with Prof. Dr. Sigmund and I trust that he speaks well English, however we conversed mostly in German at the time.


Translation:

From the Department of Mechanical Engineering, Electrical
Engineering and Industrial Engineering from the Brandenburg Technical
University of Cottbus

to obtain the academic degree of

Doctor Engineer (Dr.-Ing.)

approved dissertation

presented by

Master of Science

Hosni Taher Izweik

Born on 15.12.1954 in Zawia, Libya

Chairman: Prof. Dr.-Ing. P. Steinberg

Referee: Prof. Dr.-Ing. H. P. Berg

Referee: Prof. Dr. E. Sigmund

Date of examination:

18.11. 2009



Rolf

Thanks Rolf.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.