We encountered a rare and strange phenomena. When you have an amount
of unlimited current from a car batterycertain MOSFETs can some times
fail.
This has happened to me twice. Once when I bought an off the self
switching supply from Linear Tech and then again in Florida.
Most R&D is done with lab supplies that have some output limits on
current so this does not show up.
Surprisingly as little as ten ohms in series with the battery
prevents thisphenomena.
BTW one can tig weld with as little as 3 car batteries in series. All
you need is a tig torch and a tank of argon. Saves about a $1000 for
a real tig welder.
We will try again Aug 9th.
Paul Lamar Hi!: the idea of inserting a 10 Ohm resistor in series
with battery cable is interesting, I had some Electronic Ignition
failures that look related to the phenomenon described, however:
what kind of a 10 Ohm resistor? Where can I find this? Would the
resistance become hot as Amps start going through it, and will this
increase load to battery, thus making for the battery easier to be
exhausted? What's exactly the way of installing the resistor? Is
there somebody able to send a photo as example? Thanks for your kind
attention, have a good season. Best regards. Salud † Jose
Gros-Aymerich Madrid, Spain
Not recommended for conventional ignitions.
Paul Lamar Thanks: both my Citroën Ami-8 and my AMC Pacer have
electronic ignitions installed. See documents. I have also plans of
installing a 1987 NA RX-7 engine in a 1975 AMC Pacer X, with the
Mazda 4 speed automatic transmission. Regards. Salud †
Jose Gros-Aymerich Madrid, Spain
Still a single spark Kettering system that replaces the points with
an optical trigger and a switching transistor.
https://www.youtube.com/watch?v=fZfr-djRcIQ
http://mgaguru.com/mgtech/ignition/ig204.htm
The pacer is too heavy and too big for a 13B 161 cubic inch rotary.
What are you going to do with all the left over room in the engine
compartment ? :)
Paul Lamar
Yes, you're right, the 1975 Pacer X is 171.5 in length, 77 in wide,
and 52.8 in height, with a CD/Cx of 0.4, and it weights above
3000 lb, for a 258 6-L engine of 100 Hp at 3'600 rpm, and a
torque of 251 Nm at 1800 (figures vary according to source)
The axle ratio is 3.07:1 for 39.2 km/h/1000 rpm, the front
disc brakes are 272 mm, rear brakes are drums,
and the engine weight is 525 Lb. Wheel diameter is 641 mm.
Top speed is around 150 km/h.
The RX-7 model year 1987 is 169 in length, 66.5 in width,
49.8 in height, for a CD/Cx of 0.31, weight is 3'000 lb, the NA
engine gives 146 HP at 6'000-6'500 rpm (no agreement on this) for
an axle
ratio of 3.909:1 and 41.2 km/h for 1000 rpm, both front and rear
brakes are disks, with 276/273 cm. Wheel diameter is 627 mm.
Engine weight is around 200 lb, and the four speed auto trans
is around 60 lb. Top speed is above 200 km/h (??)
Well, I guess that changing the axle ratio in the Pacer to
4.11:1, the
top speed at 6'000-6'500 Mazda engine rpm would be in the region
of 175 km/h, acceptable for the hull, suspension, and brakes of
the Pacer.
Probably losing 300 lb of engine weight, as the engine is placed
quite
rearwards under the hood is not a major problem. I'll go on, and
let you know
what happens in the end, if you have some interest. Thanks for your
attention and the top quality technical information. Best regards.
Salud † Jose Gros-Aymerich
Madrid, Spain
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.
------------------------- <
http://www.avast.com/
This email is free from viruses and malware because avast! Antivirus
<
http://www.avast.com/ protection is active.
-------------------------
<
http://www.avast.com/
This email is free from viruses and malware because avast! Antivirus
<
http://www.avast.com/ protection is active.