Subject: mazda rotary eng for airplane
From: rotaryeng
Date: 8/16/2014, 2:44 PM
To: AA-1-Me



   Mr Paul Lamar

   I was reading your article in rotaryeng .net and saw you had a
   link to a news letter. I would like to subscribe if you are
   still sending. I would also like to ask you a question on the
   rotary engine we have installed in our aircraft. It is a six
   port intake 2006 renisis motor. We modified the intake and the
   exhaust to fit in the cowling which has resulted in a
   significant loss in horse power. We did not put in a tuned
   exhaust as you described. Could the three ports on each rotor
   be connected to a single 2.5 inch pipe and a slide throttle
   fabricated for each rotor as you did for the p-port system you
   described in the paper you wrote, then attach two  18 to 22 2.5
   inch pipes to the filter at the intake ?  You are probably very
   busy but if you could give some guidance it would be
   appreciated.

   Regards Keith A. Clayton

   Send me some pictures of the engine and I can make some
   suggestions for a better intake manifold. The HP of a rotary is
   all about the intake system. What kind of airplane is it.

   Paul Lamar

   Here are some pictures.
   Keith A. Clayton


   Assuming that you have a 2.85:1 gear box the intake runners
   need to be about 18 inches long.  That will give about 200 HP
   at 7500 RPM or so. The rotary likes to rev.  The smooth transitions
   from oval ports to round tubes is important.

   More on this in the next message

   Longer if a 2.17:1 gear box. In the second case HP will
   be 160 to 180.


   Paul Lamar

------------------------------------------------------------------------

   Here are some suggestion. If you don't care for any of these
   I can do others. Outer tubes are 2 inch OD and inner tubes
   or 1 3/4 .065 wall in both cases.

   The transitions are best done on an NC mill but could
   be done with a die grinder.


   To get 250 HP with a 2.85:1 GB you need to take it
   apart and install p-ports. In a way it is less trouble
   than 4 tubes with side ports and you get 50 HP
   additional.


   Paul Lamar



   Clayton,
         Are you a member of the Dyke Delta online group ? If not and you would like to
   join E mail me . There are two Delta's that have flown with the rotary engine and
   several more under construction . You appear to have a Tracy Crook redrive (what
   ratio ? 2.17 or 2.85 ?) and from the Maple Leaf on the tail would appear to be in
   Canada.

     Kelly Troyer


   Got any recent pictures of your Delta Kelly?


   Paul Lamar

    Paul,

    Had to go to the dark side for now.Decided I was not going to
live long enough to get my Rotary engine flying .  I have replaced it with a
Lycoming for the time being in the hope of flying in this lifetime.You
are not the only one with a few years under your beltStill working
on the rotary engine though.

Spent the last 8 years taking care of an
invalid mother which severely slowed work on the Delta.  Had to move
the Delta to my home town where mother lived (55 miles from my hangar shop)
to get any work done on it.

Was lucky to have a brother-in-law who let
me use his shop while here. After my mother passing I moved the Delta
back to my hangar recently.It was close to being ready for
inspection but in the process of towing it to the airport I had a weld
failure on the tow bar.  Damaged the nose-gear so in process of repair
(could have been much worse!!)Such is life !!<:)



Kelly Troyer

   .
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.