Subject: Note the extended point set screws more questions
From: rotaryeng
Date: 8/28/2014, 3:52 PM
To: AA-1-Me



Note the extended point set screws are better and easier to machine
than splines. All back lash is eliminated.

Paul Lamar


Hi Paul, can you give an overview on the " Note the extended point
set screws are better and easier to machine than splines. All back
lash is eliminated." I am not familar on this topic.

Thanks, Steve Carlisle

A spline (properly machined)  is proud of diameter 1. The inner shaft
is the  highest stressed part. So for max strength it should be as
large as possible.  There is a shear stress concentration at the
start of the spline and near  the root of the spline.

You can make the shaft larger diameter  with thinner wall say
diameter 2 if you use set screws. The shear stress is then
distributed over the number of screws you use.

Of course it  much much easier to machine with no broach or mill
required. Especially the female part. I know no way of doing a female
spline  with out a shaper or broach.

Just a drill press and taps are all that is required for extended
point set screws .

Tightening down the set screws removes all slop and back lash.


BTW always sign your last name as we have many Steves on here :)

Paul Lamar


Okay Paul, where in Tracy,s re-drive would you be able to use those
screws .

Steve Carlisle


Do I detect a  doubting  Steve ? :)

Since the pin fixing the input shaft to the sun gear failed twice
THAT IS WHERE THEY ARE SORELY NEEDED :) You will need 8 or 12--
3/8-24.

Paul Lamar

Hi Paul, To use set screws to fix the primary shaft into the
(hardened) sun gear, how does one drill and tap that hardened gear ?
Chris.

Get it normalized. Send the parts to me as we have a heat treater
here in Ventura. You can then get it hardened again.  Or try
normalizing just the aft end with a torch.

I was able to cut the un-needed teeth off with a carbide lathe tool.
 It is probably only case hardened so a good tap may still work. Give
 it a try. I was able to drill it as well without normalizing.

Another way  to get the un-needed teeth off is mount a small bench
grinder on your lathe cross slide.

Paul Lamar

Paul, you sent me some pics of Tracy,s PSRU, I am not sure where the
 broken bulkhead fits into the PSRU. What have been the failure
points in the PSRU and at how many hours?

Thanks again Steve Carlisle

Take another looks at the jpg's. You can see the bulkhead screwed to
 the housing.

I don't know how many hours. The sheered pins were on Dave Leonard's
 turbo. Fixed once then sheered off again. Then two larger pins as I
 recall.


The sheered bolts were on Mark Steitle's 3 rotor P-port.

IMHO extended point set screws are a major development in machine
design.

BTW you want a small amount of radial slop in the ring gear mount.
Planetary are self aligning if allowed to do so. I would give about
.050 clearance on the diameter and glue it in with RTV red rubber.
Then install the set screws but don't screw them all the way down.

Paul Lamar

Hi Paul, Got the teeth ground off the sun gear OK in my trusty old
Colechester, will try and drill/tap it today. Next question, what is
 the purpose of installing the set screws but not tightening them
down ? how has Neil done his one ? Chris.

It provides a bit of flexbilty in the ring gear so it can move around
and balance the load on all six pinion gears.

Here is a dwg of the PT6 planetary. Note the thin cone shaped
aluminum bulkhead. This gives a little so the ring gear can center on
the pinions.  A solid 1/2 thick bulkhead found in Tracy's gear box is
not near as flexible. However he did use the powder metal bulkhead
with a loose spline fit that served the propose. You must respect
this and mount the ring gear with a bit of flexibility. RTV rubber
and loose set screws will do the job.

I am not sure how Neal did it yet.


Paul Lamar

Paul, Not sure if Chris understood that the set screws will be
tightened down on the "Sun Gear" but not tightened down on the "Ring
 Gear".............

Kelly Troyer



Yep, understood all of that thanks Kelly. Chris.

What are you planning for a  torsional damper  Chris?

Paul Lamar


Hi Paul, I am going to try using a Centre flex doughnut number 22 (4
 bolt). To use untightened set screws on the ring gear, does the ring
 gear need to be countersunk ? it's as hard as hell !

Chris.

Find an EDM shop with a popper. An EDM popper puts holes in hard steal

http://www.mcmachinery.com/products-and-solutions/category/edm/edm-drill/

They only need to be .15 to .2 inches deep. Eight holes ought to do it.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.