I am selling my rotary Coot, you can fly it home or I have a trailer
that goes with it so you can also trailer it home, also I have a
couple core engines and lots of parts that go with it and all of the
molds for the plane if you want them also. Ok as for the answer why I
am selling it, I have 1600 hrs sitting in the seat and have done it
did it and been there and just moving on, probably giving up flying
as I am just running out of time to do all the things I want to do,
asking 12k for it. Ken Welter 360-834-4089 <
tel:360-834-4089
<
tel:360-834-4089 <
tel:360-834-4089
Ken Welter <
rotarycoot.ken@gmail.com
<
mailto:rotarycoot.ken@gmail.com <
mailto:rotarycoot.ken@gmail.com
<
mailto:rotarycoot.ken@gmail.com
Ken is in the Portland area. Most fun anyone can have. I have been
for a ride.
Paul Lamar
Ok may have a buyer for my Coot but they don't want the engine
package, the package includes the engine with 200hrs on it, the
redrive, prop, radiator, oil coolers, 48 DCOE Weber carb and triple
MSD ignition, one MSD fires the trailing plugs and there are 2 MSD
units that fire each leading plug, asking 4k for the package and you
can also have the engine cowling if you want it. Ken
Okay, my first impression was 1600HRS on a rotary engine, but no,
only 200. The 1600HRS on a rotary would have been impressive. I
wonder what power was in it for 1400HRS that made him want to switch
power ?
Steve Carlisle
Lots of people have more than 1400 Hours. Ken loves to tinker and he
uses NOS to up the power to 300 HP for take off.
Paul Lamar
Ken never had anything but a rotary in his Coots. The first 1400
hrs.... rotary. As Paul said, loves to tinker and likely just
re-built it. The early engines had the Ross re-drive. Ken got tired
of sending it back for repair and eventually machined and built his
own belt drive system which is what is on this motor. He had a
sprag/clutch system at one point that hooked the rotary to a 2-cycle
engine of some sort as a "back-up" motor. Good luck to you Ken..!!
bruce buksyk
Hi Bruce, thanks for the follow up on the rotary Coot. Is it right
for me to assume the backup engine was for when the re-drive failed !
Do you know what was failing in the Ross re-drive ?
Thanks, Steve Carlisle
That airplane would have been perfect for your neck of the woods
Steve. Burns auto gas.
Paul Lamar
I would takeoff and climb out with both engines running and then
shutdown the 140hp Rotax snowmobile engine and cruise on the rotary
engine but if the rotary engine were to fail I could disengage a dog
clutch on the rotary and fly on the Rotax.
The Ross gearbox had a couple failures and I had 4 engine thrust
bearing failures do to the fact that the Ross gearbox put all of the
gear thrust on the engine thrust bearing, the last engine failure was at
6,000 ft with the cloud tops at 5000 and a 500ft ceiling below but had
no problem as the Columbia river was right where the GPS said it was,
its nice having a boat under your seat.
Ken
Tracy Crook left out the sun gear thrust bearing as well in his early
design.
We have long since fixed the Ross sun gear thrust bearing problem as did
Tracy Crook in his design. That happened about 1998 to 2003. I think
Scott Speirer
discovered the problem before Ken. Maybe not. Could have been Al Wick.
Possibly before the news letter.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.