Subject: NEW GEARBOX REDUCTION IDEA Visit with Jean/MILO
From: rotaryeng
Date: 9/17/2014, 8:24 AM
To: AA-1-Me

   Paul As per today all major cars are built with front drive and
   almost built with a wheel bearing hub integrated with double ball
   bearing who act as trust in both sides and as been proof since lot
   of years..

   I found one who can be use to match the prop stubs by machining those
   hole stubs between the original wheel stubs and remove the existing
   stubs and enlarge them to remove excess weight'.

   The wheel flange have to be reduce in diameter to standard prop shaft
   size flange.

   The attached triangular flange can be machined to .200" thickness to
   reduce weight and all these parts are soft enough to be machined.

   The hub can be hold on pressure fit and with 3 long bolts from the
   inside aluminum casing and the head seal with orings to hold the oil
   pressure inside the gears chamber, or 3 long treaded studs.

   The aluminum casing can be machined from solid bar or get it cast
   from foundry, it can also be added some ribs for more stiffeness

   You can find the wheel hub bearing in Ebay at $40.00 and up depends
   on quality.

   The both shaft are about $80.00 from Slauson Transmission Parts,all
   other parts as sun gear ,planet.ring gear,front ring,drum forward
   ,bearings less then $200 from Slauson few years ago

   I am sending you several sketch showing how to built this gear box
   and it might be a few more pounds of Tracy one , much cheaper and
   fast to built with almost available parts.

   JEAN PRUDHOMME

   Jean also sent some picture of his rotary powered scale Piaggio
   Avanti he is working on. Perhaps by mistake :) Interesting nose
   gear.

   BTW Jean set your epson scanner to save as jpg instead of pdf. Then
   you can attach the jpg's to email.

   Paul Lamar


   Paul


   I just finish to extend my garage with a total length of 50 ft and
   all my tool are in place,i will have enough space to built the
   fuselage plug. I am still building my original gearbox with internal
   passage for the constant speed and install a stator. I came up with
   the hub idea for someone want to built his own cheap and fast to
   built. I do have all steel and aluminum parts for the gear box
   Include the last 2 Velocity I built from Google.com and enter N274JP
   and clic Prudhomme



   JEAN PRUDHOMME


   We were in south Florida so we visited Jean Prudhomme.

   Jean is a very prolific and talented aircraft builder. He has been
   working on airplanes since the late 60's. So far he as built nine.
   Many Velocities.

   Here are some pictures of gear box parts he intends to use on his 3/4
   scale Piaggio Avanti.

   Paul Lamar


   Jean, I assume P-1160044 JPG is a photo of an auto transmission 7A
   and a reduction housing. We are interested in the reduction housing
   for a 3.i7 reduction housing. Do you have a dimensioned sketch of
   the reduction housing? And can the housing be purchased separate
   before machining?

   Milo


   Hi Milo

   You can buy the housing from Speedway.com, is a special design but
   it have 2 side a left and a right which one of the is longer and is
   the one I do have.

   It's already machined for 85 od mm bearing at the inside housing.
   and along the inside is machined to 3.000" dia.

   For my design it is just perfect for 45mm x 85x 19 mm ball bearing
   sealed in the front and open in the back.

   You can use a constant speed propeller by drilling hole in middle of
   the shaft,

   If you machine a prop shaft in one pce you can drill bigger hole and
   lighter the weight, I will build one with the wheel bearing housing
   which I take out lot of weight

   Later I will send it to Mark Williams Enterprise to have one to be
   built with my dimensions after all adjustment been done.

   After cleanup the wheel bearing housing a 45mm id bearing fit
   perfectly without machining just add pressure fit steel collar from
   Mark Williams or any Auto Part suppliers.

   You can buy the wheel bearing housing from Ebay at $40.00 and keep
   only the flange and a bit of machining. Bearing from Ebay about
   $25.00 plus each

   My unit will be a couple of pounds more then Tracy but I am including
   a stator and also will us a constant speed MT propeller with feather
   for the twin

   I send a hand sketch to give you and idea by using the wheel bearing
   housing.

   JEAN PRUDHOMME


   Milo
   I am sending you some photos showing transmission parts shaft matching
   the other pce we need there are from Slauson less then $80 plus shipping.
   I use those as reference and the shaft for the sungear can be use by
   grinding tooths until it match the inside part of the with a press fit
   and retain by round pins as Paul suggest.
   By matting the sungear outside diameter and the inside dia shaft it will
   be stronger in shear and machine the geared wheel off


   JEAN PRUDHOMME

   jean Please Turn Bold B off in you email program.

   Paul Lamar

The casting appears to be the side bell off a mini quick change rear end. You could just press in a short piece of axle housing (3" OD) with the stub tube welded on (cheap from Speedway Engineering) and bolt on the double bearing  safety hub (full size or mini) and they will drill any bolt circle you specify. The drive plates are available in steel or aluminum and are turned by a spline on the end of custom made axles. You specify the length. Also cheap. You could also have the prop flange tight against the side bell or 20" out , or any distance, if that were needed for a balance problem. The pieces are all bullet proof. Thousands of these parts are in use every weekend across the country. The bearings are huge and gyroscopic loads would be no problem. I ran the drive plates at a small angle so I had a bit of camber and toe in on the rear tires. Just lubricate the splines in the drive plates. Still the original parts running after 7 years.

Lynn E. Hanover

   The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
   http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2014 All world wide rights reserved.