Subject: Pop rivet fix for RX8 flat tire.
From: rotaryeng
Date: 12/8/2014, 1:17 AM
To: AAA-rotaryeng


   I found a self drilling sheet metal screw in the tire. Late Sat night
   and no service stations open in town to fix flats.

   I had some 1/8th dia. 1/2 inch long pop rivets. I coated it with RTV
   and inserted into the hole and popped it in place. (I was at the
   hangar).

   I drove it 12 miles home and it lost no air pressure.

   I'll sleep with my fingers crossed.

   Paul Lamar


   After getting dinged $40 bucks to fix a flat on my truck I bought a "tire plug" kit. Only works on nail holes but that is 95% of them in my experience. Says it is only a temporary fix but I've been using it for a month.

   Darren Dyck

   I checked the air pressure this morning and it only lost a few PSI.
   If somebody wants to get rich patent and sell a kit with a special pop rivet coated
   with tire cement . Will work for up to a 1/4 inch hole. Cheaper and lighter
   than a spare tire.

   I looked in  the trunk and opened what I thought was the tool box
   that came with the 2004 RX8. Low and behold there was a high quality
   12V four bar air compressor. Made in Japan by Sumitoma Rubber Industries Ltd.

   I starting reading the owners manual for the first time in 10 years and it
   mentioned a tire can lose one psi a month. I did not know that. Also if the
   temperature changes 10 degrees F the pressure will change 1 psi.

   It also came with a large container of goo to be inserted into the tire in case
   of a leak. No spare tire. Max speed once you do that is 50 MPH. Also
   the tire is history and must be replaced.  It is called the Mazda Instant
   Mobility System. It expired in 04 2007.

   The ingredients are: Propylene Glycol, Natural Rubber, Terpene Polymer
   and Water. A good start for the coating on the pop rivet. It is limited
   to a 3/16th hole in the treed area.

   Paul Lamar


When OEM's went to R134a refrigerant from the R12, the rubber hose and
seals chemistry had to be changed. The R134a is a smaller molecule than
the R12 and it would leak out through the rubber molecules. Tires are the
same. It leaks so slow that you can not find any bubbles unless you
submerged a tire for a week and looked for small bubbles on the surface.
That might not let you see it either.


H2 is a problem to seal as it is the smallest molecule. Jay Leno had a
Hydrogen car to test. Took a holiday for two weeks and had to have it towed
to a fill station to get the tank filled as the H2 had leaked out.

CNG makes
a better clean fuel source and is easier to seal. Infrastructure is readily
available and just needs fill stations to be installed. Vehicles can be filled
overnight at home with a compressor rented from the gas Co.. After X
hours they swap them out and rebuild them covered in the rental cost.
Diesel engines run very well on CNG as it is a high octane fuel and fuel
economy should be good as the high compression recoups the lost thermal
content of natural gas.


A Dodge truck with a 318 built for propane with 13:1 CR got the same MPG
as it did previously on gasoline with 9:1 CR. burns clean but the problem is
you can not park in underground on enclosed parkades. The reason is
that a full tank could warm up when brought into a heated area from the colder
outside. Propane tanks are designed to vent if the pressure rises above a set
point to prevent rupture. The vented propane then lays on the floor and does
not disburse readily, where it is a fire hazard. Natural gas does not vent from
the high pressure tank. Any leaked gas rises to the ceiling and disburses
more readily. It is also away from cigarette butts dropped on the ground.
Just FYI.

Dale Davies


The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.