Subject: Long prop drive shaft.
From: rotaryeng
Date: 12/19/2014, 1:33 AM
To: AAA-rotaryeng



Hi Paul. I am revisiting the long drive shaft for a pusher design.
With the progress made on composite drive shaft, is the option of
long and light prop shaft becoming more of a reality now? I saw a lot
of automotive carbon shafts on the market now for very decent
prices. Could a simpler design with rubber couplings instead of
power/slip clutch be made to work without outlandish development cost
and headache? I would appreciate your thought. Luke F Wings.


How long?

I would use a minimum of 3.5 inch diameter aluminum tube. Cut the
wall thickness on a lathe to  .062" to save weight. Then anodize it
so epoxy will stick . diagonally wrap carbon fiber to a total
thickness of .125 to .2 inch.

If not too long get a stock  RX8 carbon drive shaft from a junk
yard. Yes rubber couplings are the way to go.

Paul Lamar

Will anodizing be as good as the process used on grumman GA? THANKS.
L F WINGS.

I don't know what they used on that airplane. You can buy a kit in
West Marine to treat aluminum for epoxy bonding.

How long is the prop shaft?

Paul Lamar

Isn't there a vibration issue with anodized parts. There was an award
winning Experimental helicopter where the builder had anodized a lot
of parts for a blingier look, including I think the drive shaft.
After about 60 hours the blingy part failed catastrophically causing
a complete wreck of the machine. IIRC the anodizing process
introduces microscopic stress risers. Feel free to correct me if I've
got this all buggered up.

John Gibbons


The aluminum tube is just a male mold for the carbon fiber.

BTW when you have a high modules of elasticity material (carbon)
sharing the load with a low modulus of elasticity material (aluminum)
the high modules material takes most of the load.

Paul Lamar

But when you attempt to adhesively bond two materials with widely
different Elastic Modulii you are asking for bond line failures - Ask
me how I know this Roland Friestad

I agree but not only that. When thermal expansion coefficients differ
you can also get bond line failures.

Again we are only using it as a male mold.  The carbon will take all
the load. It is too hard to remove the plug so it can be left in
there. If the bond fails it will act like a torsional damper :)

Paul Lamar



It would be better to use a tube of the correct diameter and slice it
accurately longitudinally and use it as an OUTER mould. Use pre-preg
carbon and lay it up around a partially inflated tubular balloon.
Clamp the outer mould in place and inflate the balloon whilst warming
the outer mould with a heat gun. When cured remove outer mould and
balloon and you should have a perfect carbon tube. Chris in NZ.


Chris,

That's an awesome technique.  How close in outside diameter would the layup have to be
to the inside diameter of the slit metal female mold tubing?  I would guess pretty darn close?
I wouldn't expect carbon fiber to "stretch" much, even from inflation from a 'balloon'?
Perhaps the wet layup layers actually slide over each other slightly to allow expansion to
eventually match the inside diameter of the tube?  In that case, how many layers maximum?

I wouldn't know where to get such a tubular balloon…if the prepreg could somehow be
initially adapted to the interior of the female mold, then perhaps foam could be sprayed in
the inside of the cylindrical layup…the kind of foam used in home construction work that
expands as it dries.  Just let it billow out of the ends as it expands and sets.  If there is no
adverse chemistry between that foam and the prepreg, might just leave it in place.  Could
provide a bit of structural strength and maybe even a bit of torsional damping [although if
so, would convert mechanical energy to heat…hopefully not enough to cause the carbon
tube to reach glass transition temp!!  Would need to know how much heat generated and
the overall system's ability to safely dissipate such heat without melting.]

Thanks.

Gene Kahn


The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2014 All world wide rights reserved.