Chris, your 2.85 gear set is in. Will be mailing it shortly.
Here also is a size comparison of the 2.85 front planet with the
3.12 rear planet.
Paul Lamar
Hi Paul, Looks good, does it have the splined drive boss on it for
the prop shaft, I couldn't tell from the pictures. Cheers Chris.
Not the way I would do it but yes it has aluminium female splines.
http://www.engineeringtoolbox.com/torsion-shafts-d_947.html
Shear Stress in the Shaft
When a shaft is subjected to a torque or twisting, a shearing stress
is produced in the shaft. The shear stress varies from zero in the
axis to a maximum at the outside surface of the shaft.
The shear stress in a solid circular shaft in a given position can
be expressed as:
τ = T r J (1)
where
τ = shear stress (MPa, psi)
T = twisting moment (Nmm, in lb)
r = distance from center to stressed surface in the given position
(mm, in)
J = Polar Moment of Inertia of an Area (mm^4 , in^4 )
Note
the "Polar Moment of Inertia of an Area" is a measure of a shafts's
ability to resist torsion. The "Polar Moment of Inertia" is defined
with respect to an axis perpendicular to the area considered. It is
analogous to the "Area Moment of Inertia
<
http:www.engineeringtoolbox.comarea-moment-inertia-d_1328.html" -
which characterizes a beam's ability to resist bending - required to
predict deflection and stress in a beam.
"Polar Moment of Inertia of an Area" is also called "Polar Moment of
Inertia", "Second Moment of Area", "Area Moment of Inertia", "Polar
Moment of Area" or "Second Area Moment".
Circular Shaft and Maximum Moment
Maximum moment in a circular shaft can be expressed as:
T_max = τ_max J R (2)
where
T_max = maximum twisting moment (Nmm, in lb)
τ_max = maximum shear stress (MPa, psi)
R = radius of shaft (mm, in)
Combining (2) and (3) for a solid shaft
T_max = (π 16) τ_max D^3 (2b)
Combining (2) and (3b) for a hollow shaft
T_max = (π 16) τ_max (D^4 - d^4 ) D (2c)
Circular Shaft and Polar Moment of Inertia
Polar Moment of Inertia of a circular hollow shaft can be expressed
as
J = π (D^4 - d^4 ) 32 (3b)
where
d = shaft inside diameter (mm, in)
Diameter of a Solid Shaft
Diameter of a solid shaft can calculated by the formula
D = 1.72 (T_max τ_max )^13 (4)
Torsional Deflection of Shaft
The angular deflection of a torsion shaft can be expressed as
θ = L T (J_G) (5)
where
θ = angular shaft deflection (radians
<
http:www.engineeringtoolbox.comradian-d_942.html)
L = length of shaft (mm, in)
G = modulus of rigidity
<
http:www.engineeringtoolbox.commodulus-rigidity-d_946.html (Mpa,
psi)
The angular deflection of a torsion solid shaft can be expressed as
θ = 32 L T (G π D^4 ) (5a)
The angular deflection of a torsion hollow shaft can be expressed as
θ = 32 L T (G π (D^4 - d^4 )) (5b)
The angle in degrees
<
http:www.engineeringtoolbox.comradian-d_942.html can be achieved by
multiplying the angle θ in radians with 180 π
Solid shaft (π replaced)
θ_degrees ≈ 584 L T (G D^4 ) (6a)
Hollow shaft (π replaced)
θ_degrees ≈ 584 L T (G (D^4 - d^4 ) (6b)
Bottom line hollow shafts of large diameter are lighter in weight.
If you bolt the planet carrier to a flange welded to a 2 inch OD
3/16 wall 4130 shaft you wind up with the lightest configuration with
no back lash in the spline to worry about.
Paul Lamar
Sorry I haven’t been following this thread…is this a PSRU? and if so
how do I get one for 13b that had an automatic transmission. Thx,
Byron Head
Yes. Chris is building one in New Zealand, Neal is building some in
OZ and I think Randy will be building some in Colorado.
Where are you?
Paul Lamar
I will be building one in South Africa
Le Roux Breytenbach
BTW Old Lou Ross got the design right back in 1973 except for the
prop flange attachment and the helical gear thrust bearing. Extended
point set screws were not invented yet. If you weld the planet
carrier flange to the 2 inch hollow prop shaft you must be able to
unscrew the prop flange for over haul and maintenance. That is where
the extended point set screws come into play.
The torque input to the prop shaft comes from the planet shafts. The
torque output goes into the prop bolts. The shortest load path is a
large hollow shaft. We call this the idealized prop shaft.
Before you build an idealized prop shaft think about the RPM of the
needles in the bearings :)
Paul Lamar
Paul,
I am in Los Angeles if that makes a difference……the 13b is from an RX8
that had
an automatic tranny…..so if they are being built in Colorado any idea
when they will be available?
thx,
Byron
My guess is sometime after April.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.