Subject: 2.85 to 1 Ford gear set
From: paul
Date: 2/10/2015, 9:44 PM
To: AAA-rotaryengine



Chris, your 2.85 gear set is in. Will be mailing it shortly.

Here also is a size comparison of the 2.85 front planet with the 3.12 rear planet.

Paul Lamar


Hi Paul, Looks good, does it have the splined drive boss on it for the prop shaft, I couldn't tell from the pictures. Cheers Chris.


Not the way I would do it but yes it has aluminium female splines.

http://www.engineeringtoolbox.com/torsion-shafts-d_947.html

Shear Stress in the Shaft

When a shaft is subjected to a torque or twisting, a shearing stress is produced in the shaft. The shear stress varies from zero in the axis to a maximum at the outside surface of the shaft.

The shear stress in a solid circular shaft in a given position can be expressed as:

τ = T r  J     (1)

where

τ = shear stress (MPa, psi)

T = twisting moment (Nmm, in lb)

r = distance from center to stressed surface in the given position (mm, in)

J = Polar Moment of Inertia of an Area (mm^4 , in^4 )

Note

the "Polar Moment of Inertia of an Area" is a measure of a shafts's ability to resist torsion. The "Polar Moment of Inertia" is defined with respect to an axis perpendicular to the area considered. It is analogous to the "Area Moment of Inertia <http:www.engineeringtoolbox.comarea-moment-inertia-d_1328.html" - which characterizes a beam's ability to resist bending - required to predict deflection and stress in a beam.

"Polar Moment of Inertia of an Area" is also called "Polar Moment of Inertia", "Second Moment of Area", "Area Moment of Inertia", "Polar Moment of Area" or "Second Area Moment".


Circular Shaft and Maximum Moment

Maximum moment in a circular shaft can be expressed as:

T_max = τ_max J  R         (2)

where

T_max = maximum twisting moment (Nmm, in lb)

τ_max = maximum shear stress (MPa, psi)

R = radius of shaft (mm, in)

Combining (2) and (3) for a solid shaft

T_max = (π  16) τ_max D^3          (2b)

Combining (2) and (3b) for a hollow shaft

T_max = (π  16) τ_max (D^4 - d^4 )  D         (2c)


Circular Shaft and Polar Moment of Inertia



Polar Moment of Inertia of a circular hollow shaft can be expressed as

J = π (D^4 - d^4 )  32         (3b)

where

d = shaft inside diameter         (mm, in)


Diameter of a Solid Shaft

Diameter of a solid shaft can calculated by the formula

D = 1.72 (T_max  τ_max )^13          (4)


Torsional Deflection of Shaft

The angular deflection of a torsion shaft can be expressed as

θ = L T  (J_G)         (5)

where

θ = angular shaft deflection (radians
<http:www.engineeringtoolbox.comradian-d_942.html)

L = length of shaft (mm, in)

G = modulus of rigidity
<http:www.engineeringtoolbox.commodulus-rigidity-d_946.html (Mpa,
psi)

The angular deflection of a torsion solid shaft can be expressed as

θ = 32 L T  (G π D^4 )         (5a)

The angular deflection of a torsion hollow shaft can be expressed as

θ = 32 L T  (G π (D^4 - d^4 ))         (5b)

The angle in degrees
<http:www.engineeringtoolbox.comradian-d_942.html can be achieved by multiplying the angle θ in radians with 180  π

Solid shaft (π replaced)

θ_degrees ≈ 584 L T  (G D^4 )         (6a)

Hollow shaft (π replaced)

θ_degrees  ≈ 584 L T  (G (D^4 - d^4 )         (6b)



Bottom line hollow shafts of large diameter are lighter in weight. If you bolt the planet carrier to a flange welded to a 2 inch OD 3/16 wall 4130 shaft you wind up with the lightest configuration with no back lash in the spline to worry about.

Paul Lamar

Sorry I haven’t been following this thread…is this a PSRU?  and if so how do I get one for 13b that had an automatic transmission.
Thx, Byron Head

Yes.
Chris is building one in New Zealand, Neal is building some in OZ and I think  Randy will be building some in Colorado.
Where are you?

Paul Lamar

Hi Byron,
       I am building a PSRU to fit on the back of a 13B/RX8 automatic bell housing, 2.85/3.17 ratio. I like the auto housing as it puts the starter in the best place for C of G purposes.
                       Chris in NZ.


The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http:www.rotaryeng.net You Tube http:tinyurl.combeqqxas Copyright
1998-2015 All world wide rights reserved.