Subject: for sale 20B Tracy EFI won't start
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 2/13/2015, 4:47 PM
To: AA-1-Me



   Anyone know if Tracy is still providing any technical support, or is he done
   completely?

   Jay Jacobs



   Tracy is definitely providing technical support.  He is retiring because
   he is getting to the age where he wants to do something different with
   his time.

   Dave Leonard

   Thanks David

   I've got an interested buyer for my 20B but he wants to see it run first.
   Several years ago I couldn’t get it to start.  Turns out the EC had not
   been
   properly programmed.
   By the time I got the repaired EC back from Tracy my project had been set
   aside. Only now I still can't get the engine to start.

   Jay Jacobs


   Put a long screw driver next to your ear and touch the injectors
   one by one. You should hear a click when the injector operates.

   I assume you have spark.


   Take the lower plugs out and put a table spoon of auto TX oil in each rotor.

   If you have a compressor.. Find a 3/4 or one inch drive socket that fits
    the large nut  on the front of the e-shaft.
   Use a large air wrench to turn the engine over at high speed .

   No compressor  use two
   12 volt batteries in series to turn the engine over at high speed with
   the starter
   running on 24 volts. Only do this for a few seconds. Then stop and let the
   starter cool.

   Get some either starting fluid. Spray that into the intake.
    If the timing is set correctly it should fire a couple of times.
   If not you have a mixture problem.

   If you have the exhaust off check the apex seals for in an out motion
   with a screw driver.


   Paul Lamar


   With the Fuel OFF, there is a setting of the EC-2 (and presumably the EC-3)
   where pushing the  button will cause continuous firing of the injectors. I
   am away from my manuals right now but I believe that it is setting 1 on the
   mode button. There is also one setting the will fire the plugs.

   Best if fuel is off, otherwise you will flood the engine.
   Bill Schertz


   Yes Bill it's mode 8 and mode 0.  Both injectors and plugs are firing on the
   B side of the EC. Nether of them test fire on the A side.

   I tried Paul's air gun suggestion but apparently 150 psi isn't enough to
   turn over the engine.

   Jay


   What size is the square plug on the air gun, 3/4 or 1 inch? (for future reference)
   The larger the plug the stronger the air wrench.

   My 3/4 puts out 500 foot pounds at 4500 RPM with 90 psi. Harbor Freight special.

   That ought to do it :)


   Paul Lamar


Can you hand turn the engine? Another way if the engine will turn is to use a 1/2" drill. Just screw a fairly long piece of 1/2" pipe into the threads on the side opposite the trigger. A 1/2" bolt welded to a piece of 1/2" key stock or a cheap socket to drive the pulley bolt. Years ago I had a R100 with only 40LBS compression. I kept a quart bottle of oil under the hood. A gear oil bottle has a small top and I could put a small amount down the carb if the revs dropped below 1300 at a light as it would stall. My buddies called it "doing a smoky" as there would be a cloud as high as a street light but it got it fired up. I finally put a 12A in as in Canada you can not buy overhaul parts through Mazda Canada. Just exchange reman engines.

Maybe at that time I could have gotten parts from Racing Beat sent up. I bent the R100 and put the drive train into a 1200 Coupe. Should have kept the 1200 stock. It ran well and got 50Imp MPG. So much for all the MPG improvements. The car ran like a top but the 1200 was about 300 pounds lighter than the R100 due to extra bracing in the R100 body shell. Went like a raped ape with the 12A in a 1600 pound car. Scary as hell when it came time to slow down though!

Dale Davies


   The Rotary Engine News Letter. Powered by Linux.
   ACRE NL web site. http://www.rotaryeng.net
   You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2015 All world wide rights reserved.