Anyone know if Tracy is still providing any technical support, or
is he done
completely?
Jay Jacobs
Tracy is definitely providing technical support. He is retiring
because
he is getting to the age where he wants to do something different with
his time.
Dave Leonard
Thanks David
I've got an interested buyer for my 20B but he wants to see it run
first.
Several years ago I couldn’t get it to start. Turns out the EC had not
been
properly programmed.
By the time I got the repaired EC back from Tracy my project had
been set
aside. Only now I still can't get the engine to start.
Jay Jacobs
Put a long screw driver next to your ear and touch the injectors
one by one. You should hear a click when the injector operates.
I assume you have spark.
Take the lower plugs out and put a table spoon of auto TX oil in
each rotor.
If you have a compressor.. Find a 3/4 or one inch drive socket that
fits
the large nut on the front of the e-shaft.
Use a large air wrench to turn the engine over at high speed .
No compressor use two
12 volt batteries in series to turn the engine over at high speed with
the starter
running on 24 volts. Only do this for a few seconds. Then stop and
let the
starter cool.
Get some either starting fluid. Spray that into the intake.
If the timing is set correctly it should fire a couple of times.
If not you have a mixture problem.
If you have the exhaust off check the apex seals for in an out motion
with a screw driver.
Paul Lamar
With the Fuel OFF, there is a setting of the EC-2 (and presumably
the EC-3)
where pushing the button will cause continuous firing of the
injectors. I
am away from my manuals right now but I believe that it is setting
1 on the
mode button. There is also one setting the will fire the plugs.
Best if fuel is off, otherwise you will flood the engine.
Bill Schertz
Yes Bill it's mode 8 and mode 0. Both injectors and plugs are
firing on the
B side of the EC. Nether of them test fire on the A side.
I tried Paul's air gun suggestion but apparently 150 psi isn't
enough to
turn over the engine.
Jay
What size is the square plug on the air gun, 3/4 or 1 inch? (for
future reference)
The larger the plug the stronger the air wrench.
My 3/4 puts out 500 foot pounds at 4500 RPM with 90 psi. Harbor
Freight special.
That ought to do it :)
Paul Lamar
Can you hand turn the engine? Another way if the engine will turn is to
use a 1/2" drill. Just screw a fairly long piece of 1/2" pipe into the
threads on the side opposite the trigger. A 1/2" bolt welded to a piece
of 1/2" key stock or a cheap socket to drive the pulley bolt. Years ago
I had a R100 with only 40LBS compression. I kept a quart bottle of oil
under the hood. A gear oil bottle has a small top and I could put a
small amount down the carb if the revs dropped below 1300 at a light as
it would stall. My buddies called it "doing a smoky" as there would be a
cloud as high as a street light but it got it fired up. I finally put a
12A in as in Canada you can not buy overhaul parts through Mazda Canada.
Just exchange reman engines.
Maybe at that time I could have gotten parts from Racing Beat sent up. I
bent the R100 and put the drive train into a 1200 Coupe. Should have
kept the 1200 stock. It ran well and got 50Imp MPG. So much for all the
MPG improvements. The car ran like a top but the 1200 was about 300
pounds lighter than the R100 due to extra bracing in the R100 body
shell. Went like a raped ape with the 12A in a 1600 pound car. Scary as
hell when it came time to slow down though!
Dale Davies
"for future reference", my air gun is a 1/2" drive and compressor is 150 psi
I also have a 32mm socket for the nut on the e-shaft
Together they don't even budge the engine
I have two 12v aircraft batts wired in parallel powering everything right
now
I'll have to jury rig a little wiring to get 24v going to the starter only
I do have starter spray/fluid, whatever you call it, though I haven't tried
it yet this time
Just eyeballing it I don't think any drill I have is going to do any better
than the air gun at turning the engine over either
Although the idea of being able to rotate the engine for longer periods,
without burning up the starter, sure is appealing
Jay
It is too small Jay unless the engine is seized.
Borrow or rent a heavy duty 3/4. How much HP is your air compressor?.
My 3/4 is rated for 7/8th bolts.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.