Subject: for sale 20B Tracy EFI won't start
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 2/15/2015, 6:30 AM
To: AA-1-Me




   Anyone know if Tracy is still providing any technical support, or
   is he done
   completely?

   Jay Jacobs



   Tracy is definitely providing technical support.  He is retiring
   because
   he is getting to the age where he wants to do something different with
   his time.

   Dave Leonard

   Thanks David

   I've got an interested buyer for my 20B but he wants to see it run
   first.
   Several years ago I couldn’t get it to start.  Turns out the EC had not
   been
   properly programmed.
   By the time I got the repaired EC back from Tracy my project had
   been set
   aside. Only now I still can't get the engine to start.

   Jay Jacobs


   Put a long screw driver next to your ear and touch the injectors
   one by one. You should hear a click when the injector operates.

   I assume you have spark.


   Take the lower plugs out and put a table spoon of auto TX oil in
   each rotor.

   If you have a compressor.. Find a 3/4 or one inch drive socket that
   fits
    the large nut  on the front of the e-shaft.
   Use a large air wrench to turn the engine over at high speed .

   No compressor  use two
   12 volt batteries in series to turn the engine over at high speed with
   the starter
   running on 24 volts. Only do this for a few seconds. Then stop and
   let the
   starter cool.

   Get some either starting fluid. Spray that into the intake.
    If the timing is set correctly it should fire a couple of times.
   If not you have a mixture problem.

   If you have the exhaust off check the apex seals for in an out motion
   with a screw driver.


   Paul Lamar


   With the Fuel OFF, there is a setting of the EC-2 (and presumably
   the EC-3)
   where pushing the  button will cause continuous firing of the
   injectors. I
   am away from my manuals right now but I believe that it is setting
   1 on the
   mode button. There is also one setting the will fire the plugs.

   Best if fuel is off, otherwise you will flood the engine.
   Bill Schertz


   Yes Bill it's mode 8 and mode 0.  Both injectors and plugs are
   firing on the
   B side of the EC. Nether of them test fire on the A side.

   I tried Paul's air gun suggestion but apparently 150 psi isn't
   enough to
   turn over the engine.

   Jay


   What size is the square plug on the air gun, 3/4 or 1 inch? (for
   future reference)
   The larger the plug the stronger the air wrench.

   My 3/4 puts out 500 foot pounds at 4500 RPM with 90 psi. Harbor
   Freight special.

   That ought to do it :)


   Paul Lamar


   Can you hand turn the engine? Another way if the engine will turn is to
   use a 1/2" drill. Just screw a fairly long piece of 1/2" pipe into the
   threads on the side opposite the trigger. A 1/2" bolt welded to a piece
   of 1/2" key stock or a cheap socket to drive the pulley bolt. Years ago
   I had a R100 with only 40LBS compression. I kept a quart bottle of oil
   under the hood. A gear oil bottle has a small top and I could put a
   small amount down the carb if the revs dropped below 1300 at a light as
   it would stall. My buddies called it "doing a smoky" as there would be a
   cloud as high as a street light but it got it fired up. I finally put a
   12A in as in Canada you can not buy overhaul parts through Mazda Canada.
   Just exchange reman engines.

   Maybe at that time I could have gotten parts from Racing Beat sent up. I
   bent the R100 and put the drive train into a 1200 Coupe. Should have
   kept the 1200 stock. It ran well and got 50Imp MPG. So much for all the
   MPG improvements. The car ran like a top but the 1200 was about 300
   pounds lighter than the R100 due to extra bracing in the R100 body
   shell. Went like a raped ape with the 12A in a 1600 pound car. Scary as
   hell when it came time to slow down though!

   Dale Davies



   "for future reference", my air gun is a 1/2" drive and compressor is 150 psi
   I also have a 32mm socket for the nut on the e-shaft
   Together they don't even budge the engine

   I have two 12v aircraft batts wired in parallel powering everything right
   now
   I'll have to jury rig a little wiring to get 24v going to the starter only

   I do have starter spray/fluid, whatever you call it, though I haven't tried
   it yet this time

   Just eyeballing it I don't think any drill I have is going to do any better
   than the air gun at turning the engine over either
   Although the idea of being able to rotate the engine for longer periods,
   without burning up the starter, sure is appealing

   Jay


   It is too small Jay unless the engine is seized.
   Borrow or rent a heavy duty 3/4. How much HP is your air compressor?.
   My 3/4 is rated for 7/8th bolts.

   Paul Lamar

My Snap-On and Mac 1/2" impact wrenches are rated to 500Lbs and have been used to remove wheel nuts from Class 8 trucks. The problem with using an impact wrench to turn the engine over is the intermitent torque pulses as the hammers hit and release. A 1/2" electric drill keeps the torque applied. A 1/2" electric drill can break your wrist if the bit catches. Sounds like the engine may be seized. If you can not turn it over by hand with the flywheel, you need to solve that issue first. Even turning it over with a 12 volt battery and the starter, you should be able to hear even pops out the exhaust ports if it is healthy.

Dale Davies

1/2 air wrendh must come  in different sizes.  mine is about 2 and 3/4 inch in diameter
and weighs 5 pounds. My 3/4 is about 3 1/4 inches in diameter and weighs 11 pounds.
It takes about 20 ft pounds to turn my 3 rotor over.

Paul Lamar



    The Rotary Engine News Letter. Powered by Linux.
   ACRE NL web site. http://www.rotaryeng.net
   You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2015 All world wide rights reserved.