Subject: for sale 20B Tracy EFI won't start
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 2/15/2015, 12:19 PM
To: AA-1-Me

Anyone know if Tracy is still providing any technical support, or
is he done
completely?

Jay Jacobs



Tracy is definitely providing technical support.  He is retiring
because he is getting to the age where he wants to do something
different with his time.

Dave Leonard

Thanks David

I've got an interested buyer for my 20B but he wants to see it run
first. Several years ago I couldn’t get it to start.  Turns out the EC
had not
been properly programmed.
By the time I got the repaired EC back from Tracy my project had
been set aside. Only now I still can't get the engine to start.

Jay Jacobs


Put a long screw driver next to your ear and touch the injectors
one by one. You should hear a click when the injector operates.

I assume you have spark.


Take the lower plugs out and put a table spoon of auto TX oil in
each rotor.

If you have a compressor.. Find a 3/4 or one inch drive socket that
fits
 the large nut  on the front of the e-shaft.
Use a large air wrench to turn the engine over at high speed .

No compressor  use two
12 volt batteries in series to turn the engine over at high speed with
the starter
running on 24 volts. Only do this for a few seconds. Then stop and
let the starter cool.

Get some either starting fluid. Spray that into the intake.
 If the timing is set correctly it should fire a couple of times.
If not you have a mixture problem.

If you have the exhaust off check the apex seals for in an out motion
with a screw driver.


Paul Lamar


With the Fuel OFF, there is a setting of the EC-2 (and presumably
the EC-3)
where pushing the  button will cause continuous firing of the
injectors. I
am away from my manuals right now but I believe that it is setting
1 on the
mode button. There is also one setting the will fire the plugs.

Best if fuel is off, otherwise you will flood the engine.
Bill Schertz


Yes Bill it's mode 8 and mode 0.  Both injectors and plugs are
firing on the
B side of the EC. Nether of them test fire on the A side.

I tried Paul's air gun suggestion but apparently 150 psi isn't
enough to
turn over the engine.

Jay


What size is the square plug on the air gun, 3/4 or 1 inch? (for
future reference)
The larger the plug the stronger the air wrench.

My 3/4 puts out 500 foot pounds at 4500 RPM with 90 psi. Harbor
Freight special.

That ought to do it :)


Paul Lamar


Can you hand turn the engine? Another way if the engine will turn is to
use a 1/2" drill. Just screw a fairly long piece of 1/2" pipe into the
threads on the side opposite the trigger. A 1/2" bolt welded to a piece
of 1/2" key stock or a cheap socket to drive the pulley bolt. Years ago
I had a R100 with only 40LBS compression. I kept a quart bottle of oil
under the hood. A gear oil bottle has a small top and I could put a
small amount down the carb if the revs dropped below 1300 at a light as
it would stall. My buddies called it "doing a smoky" as there would
be a
cloud as high as a street light but it got it fired up. I finally put a
12A in as in Canada you can not buy overhaul parts through Mazda
Canada.
Just exchange reman engines.

Maybe at that time I could have gotten parts from Racing Beat sent
up. I
bent the R100 and put the drive train into a 1200 Coupe. Should have
kept the 1200 stock. It ran well and got 50Imp MPG. So much for all the
MPG improvements. The car ran like a top but the 1200 was about 300
pounds lighter than the R100 due to extra bracing in the R100 body
shell. Went like a raped ape with the 12A in a 1600 pound car. Scary as
hell when it came time to slow down though!

Dale Davies



"for future reference", my air gun is a 1/2" drive and compressor
is 150 psi I also have a 32mm socket for the nut on the e-shaft
Together they don't even budge the engine

I have two 12v aircraft batts wired in parallel powering everything
right now I'll have to jury rig a little wiring to get 24v going to the
starter only

I do have starter spray/fluid, whatever you call it, though I
haven't tried it yet this time

Just eyeballing it I don't think any drill I have is going to do
any better than the air gun at turning the engine over either
Although the idea of being able to rotate the engine for longer
periods, without burning up the starter, sure is appealing

Jay


It is too small Jay unless the engine is seized.
Borrow or rent a heavy duty 3/4. How much HP is your air compressor?.
My 3/4 is rated for 7/8th bolts.

Paul Lamar

My Snap-On and Mac 1/2" impact wrenches are rated to 500Lbs and have
been used to remove wheel nuts from Class 8 trucks. The problem with
using an impact wrench to turn the engine over is the intermitent torque
pulses as the hammers hit and release. A 1/2" electric drill keeps the
torque applied. A 1/2" electric drill can break your wrist if the bit
catches. Sounds like the engine may be seized. If you can not turn it
over by hand with the flywheel, you need to solve that issue first. Even
turning it over with a 12 volt battery and the starter, you should be
able to hear even pops out the exhaust ports if it is healthy.

Dale Davies

1/2 air wrendh must come  in different sizes.  mine is about 2 and 3/4
inch in diameter and weighs 5 pounds. My 3/4 is about 3 1/4 inches in
diameter and weighs11 pounds. It takes about 20 ft pounds
to turn my 3 rotor over.

Paul Lamar



My engine turns over easily with the starter  The tach apparently isn't
hooked up properly so I don't know at what rpm it's turning

Jay Jacobs


When the apex seals are sticking and leaking it takes a lot of RPM to start
the engine the first time. Once it warms up the gunk holding the apex
seal softens and the engine starts easier the next time. The gunk comes
from using
mineral oil and not synthetic oil. The apex seal runs at 500 F and that
turns mineral oil to sludge. If you use two cycle oil premix that problem
goes away. I run Mobil 1 or Idemitsu in my RX8 and it sits in the hangar
sometimes for
a couple of months with the battery disconnected. It always starts
immediately
after I hook up the battery again.

Mobil 1 does not deteriorate too bad at 500 F.


Paul Lamar


I'm using premix in my fuel although no doubt the fact it's never run is a
factor in getting it to for the 1st time
I think I'm just going to rent an electric 3/4" drill That way I don't have
to rearrange the current wiring or abuse the starter

Jay

I use my half inch drill motor to start a B & S one cyl with a one way clutch.

    pics

Paul Lamar



    If the drill wont get it started, it should keep it turning after the starter gets
    it going provided you have a big enough drill. To get the mazda engine
    turning will take a lot bigger drill than is in this series of pics.

    Kevin Alderman

    Of course :)


    Paul Lamar

This should do it if you can hold it. If you were close to Jacksonville FL, I have 2. I can loan you one.

Kevin Alderman



 The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.