Paul As per today all major cars are built with front drive and
almost built with a wheel bearing hub integrated with double ball
bearing who act as trust in both sides and as been proof since lot of
years..
I found one who can be use to match the prop stubs by machining
those hole stubs between the original wheel stubs and remove the
existing stubs and enlarge them to remove excess weight'.
The wheel flange have to be reduce in diameter to standard prop
shaft size flange.
The attaché triangular flange can be machined to .200" thickness to
reduce weight and all these parts are soft enough to be machined.
The hub can be hold on pressure fit and with 3 long bolts from the
inside aluminum casing and the head seal with orings to hold the oil
pressure inside the gears chamber, or 3 long treaded studs.
The aluminum casing can be machined from solid bar or get it cast
from foundry, it can also be added some ribs for more stiffeness
You can find the wheel hub bearing in Ebay at $40.00 and up depends
on quality.
The both shaft are about $80.00 from Slauson Transmission Parts,all
other parts as sun gear ,planet.ring gear,front ring,drum forward
,bearings less then $200 from Slauson few years ago
I am sending you several sketch showing how to built this gear box
and it might be a few more pounds of Tracy one , much cheaper and fast
to built with almost available parts.
JEAN PRUDHOMME
Jean also sent some picture of his rotary powered scale Piaggio
Avanti he is working on. Perhaps by mistake :) Interesting nose gear.
BTW Jean set your epson scanner to save as jpg instead of pdf. Then
you can attach the jpg's to email.
Paul Lamar
Paul
I just finish to extend my garage with a total length of 50 ft and
all my tool are in place,i will have enough space to built the fuselage
plug. I am still building my original gearbox with internal passage for
the constant speed and install a stator. I came up with the hub idea for
someone want to built his own cheap and fast to built. I do have all
steel and aluminum parts for the gear box Include the last 2 Velocity I
built from Google.com and enter N274JP and clic Prudhomme
JEAN PRUDHOMME
We were in south Florida so we visited Jean Prudhomme.
Jean is a very prolific and talented aircraft builder. He has been
working on airplanes since the late 60's. So far he as built nine.
Many Velocities.
Here are some pictures of gear box parts he intends to use on his
34 scale Piaggio Avanti.
Paul Lamar
Jean, I assume P-1160044 JPG is a photo of an auto transmission 7A
and a reduction housing. We are interested in the reduction housing for
a 3.i7 reduction housing. Do you have a dimensioned sketch of the
reduction housing? And can the housing be purchased separate before
machining?
Milo
Hi Milo
You can buy the housing from Speedway.com, is a special design but
it have 2 side a left and a right which one of the is longer and is the
one I do have.
It's already machined for 85 od mm bearing at the inside housing.
and along the inside is machined to 3.000" dia.
For my design it is just perfect for 45mm x 85x 19 mm ball bearing
sealed in the front and open in the back.
You can use a constant speed propeller by drilling hole in middle
of the shaft,
If you machine a prop shaft in one pce you can drill bigger hole
and lighter the weight, I will build one with the wheel bearing housing
which I take out lot of weight
Later I will send it to Mark Williams Enterprise to have one to be
built with my dimensions after all adjustment been done.
After cleanup the wheel bearing housing a 45mm id bearing fit
perfectly without machining just add pressure fit steel collar from Mark
Williams or any Auto Part suppliers.
You can buy the wheel bearing housing from Ebay at $40.00 and keep
only the flange and a bit of machining. Bearing from Ebay about
$25.00 plus each
My unit will be a couple of pounds more then Tracy but I am
including a stator and also will us a constant speed MT propeller with
feather for the twin
I send a hand sketch to give you and idea by using the wheel
bearing housing.
JEAN PRUDHOMME
Milo I am sending you some photos showing transmission parts shaft
matching the other pce we need there are from Slauson less then $80 plus
shipping. I use those as reference and the shaft for the sungear can be
use by grinding tooths until it match the inside part of the with a
press fit and retain by round pins as Paul suggest. By matting the
sungear outside diameter and the inside dia shaft it will be stronger in
shear and machine the geared wheel off
JEAN PRUDHOMME
jean Please Turn Bold B off in you email program.
Paul Lamar
Jean I may have miss led you. I am an amateur at this game. We are
interested in using an automatic Xmission bell housing like you show in
your photo's with a nose piece as shown for a 3.17 setup and different
from you we wish to salvage the use of a prop shaft of an IO 540
Lycoming engine that we have in hand that has 2 flanges to work with and
for taking up thrust loads in particular and dispense with the necessity
of screwing the hub on the shaft for experimental purposes. Your
extensive back ground has proven a big help and with your permission we
will tag along, right now everything is up in the air but with guys like
you and paul we are making good progress. I am fascinated with the
number combinations possible using standard automotive components, we
like aircraft pieces, especially hubs and etc., to test with just to get
data.
Milo
Let me clarify this a bit more. Milo is using recycled Lycoming
crank shafts that are typically cracked in the first journal fillet
area. The case is split and then bolted together just like a Lycoming
crank case.
This accommodates a stock prop gov and CS prop.
Paul Lamar
Hi Milo
I just turned the rough shaft but I nee to make treads at flange
ends and atrear bearing,splines to hold the front flange and threads to
hold the rear bearing trust ( I can use a opessure fit collar but it
will be easyer to adjust the rear bearing to prevent excess load and few
thousands for metal expansion.
I will get the rest to be done on a machine shop near buy, i only
have small lathe, the guy will charge me $50.00 an hour to cut the
treads and splines.
I need a bigger lathe to machine the 12' back plate and other alum
part to hold the stator I am sending you photos of the shaft with
component, the planet side is to long and I will cut the excess after
assembly adjustment.
Paul I received the BLU STUDIO 5.5 as a phone ,you is it with
intercom when you received a call which is not convenient for me.
Do you have the shock mount cup drawing I will need to design the
alum plate .
JEAN PRUDHOMME
i am not sure what you need but here is our latestest thinking on that.
I have some parts made if you need them.
Paul Lamar
Hi Paul,
Do you have the dimensions and material thickness for the damper.
Andrew Campbell.
The billet material is 6061 T6 or 7075 T6 if you can find it.
Do you have an NC Mill? Could also be done with a rotary table and
a reg mill.
Could also be welded up out of 3/16th thick 4130 sheet and trued up
on a lathe.
Dwgs a few days.
Paul Lamar
Jean-- have a nice 16 inch lath with a 16' plate, 5hp variable
speed digital mill, etc.but I am a butcher with very little patience,
and almost no experience, no heat in the shop. You are welcome to come
here and use everything I have, the 16" lathe is too big to ship.
If it’s a simple turning job I'll give it a shot
Milo
Now the bad part the wife and I are quit, don't smoke, take drugs,
drink..socialize, and I don't like people generally(dull) and if you get
to be a pest will ask you to leave. My wife is a Masters in Mechanical
EnGr. Works hard all day, not a servant.
Now if you thought this was was going to be for free. I am going
to pick you brain endlessly!
MILO
LoL Milo, your funny...
GFC
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http:www.rotaryeng.net <http://www.rotaryeng.net> You Tube
http:tinyurl.combeqqxas Copyright 1998-2014 All world wide rights reserved.