It amazes me what people will put up with to burn kerosene. .82
lb/(hp-hr) and they talk like its the greatest thing since sliced
bread. 19 gph! compared to 11.5 running lean with the IO-540. The
world really really needs a heavy-fuel-burning rotary! And this
article - is Amy smart enough to realize that if the CG difference
makes the plane feel so much different than her IO-540 RV-10, it
might mean there could be an aft CG issue with 4 people and bags?
Might that be something to discuss in a flight review article?
David Bonorden
I would never buy one. Diesel fumes stink and they are
carcinogenic. Packard figured that out in 1930"s. The power to
weight ratio sucks.
Diesel should only be used in trucks and ships. The only reason it
is popular in European cars is the tax is a dollar a gallon less.
If they taxed it as high as gasoline ($7 or$ 8 gallon) it would
seriously affect the European economy.
----------------------------------------------------------------------------
C172 gasoline verses C172 diesel data from the Cessna web site.
Diesel fuel is a pound heavier than gasoline. Gas is six pounds per
gallon and diesel is 7 pounds per gallon.
44.6 gallons of diesel weighs 312 pounds of fuel.
Max useful load on a Diesel C172 is 742 pounds. Subtract the full
fuel weight and you get 430 pounds. Range is 588 nm. 85% power is
132 HP. Cruise speed at 85% power is 118 kts or 5 hours.
8.9 gallons an hour or 62.5 pounds per hour. BSFC is therefore .47.
Not a lot different than a fully leaned Mazda rotary. And typical
for a diesel engine running near full power.
How can this be? Everybody knows that diesel cars get much better
mileage than gasoline powered cars. The fact is diesel engines
running near full power are not much better than gasoline engines
based on a HP per pound of fuel burned. See the attached chart.
A leaned Mazda rotary at 132 HP would be about the same BSFC but
the gallons per hour would be higher at 62.5/6 or 10.4 gallons per
hour.
A turbo compound rotary on the other hand would be down in the
below .4 range or about the same as a truck diesel running at 50%
power.
------------------------------------------------------ The numbers
for a stock Lycoming powered C172 are:
56 gallons of gasoline weighs 336 pounds of fuel. Max useful load
is 758 pounds. Subtract the full fuel weight and you get 422
pounds. Range is 580 nm. 80% power is 128 HP. Cruise speed at 80%
power is 122 Kts or 4.8 hours.
Four kts faster than the diesel.
11.8 gallons an hour or 69.6 pounds per hour. BSFC is therefore .54
which is a typical for a Lycoming rich of peak.
It would take a long time to pay for the extra $15,000 you will pay
for a diesel powered Cessna 172.
Not to mention you are required to throw the diesel away at 1200
hours if it does not pass detailed inspection. No overhaul
allowed. If it does pass 1200 hour detailed inspection you are
required to throw it away at 2400 hours. No exceptions.
At 100 hours a year that is 24 years. At that point the Mercedes A
class diesel engine will probably no longer be available so the air
plane, in theory, will be worthless. One would have to replace the
engine now certified in the Mercedes A class diesel powered Cessna
172 with some other engine and obtain an FAA one time STC.
I don't see it.
Do you want to tow or do you want to go?
Paul Lamar A hobbyist doubt: if the density of Diesel fuel, the
weight per volume, is higher: would this mean that in a liter of
Diesel fuel there are more Carbon and Hydrogen molecules to be
burnt, and thus, the power density of fuel is better, a liter of
Diesel yields more heat when burnt, this adding to explain the
better SFC of Diesels in terms of gr/kW/hr, besides the better
thermal efficiency from the much higher Compression Ratio, or this
was taken into account in Diesel vs Gasoline SFC figures?
I've learned from this e-mail about the meaning of 'Thermal load'
inside an Internal Combustion Engine, HP per surface of combustion
chamber, and MEP, I remembered having read about the worries of
the early Air-Cooled Wankel Engine designers about increasing CR
and Power, because of the dangers of thermal load (on bearings and
shafts?), and on the lubricating oil film, but the chart you added
indicates an extremely low thermal load for the only RCE on it, a
Mistral. Is this because of the poor MEP of Wankel, or for other
reasons?
The high surface to volume ratio of Wankel RCE combustion chamber
was blamed for the improvable fuel economy, but the surface/volume
ratio in the time of top compression may not be the same during
the process of expansion, where the working chamber volume
increases, both in the irregular shaped Wankel and in the classical
cylinder. How does the plot of surface/volume ratio changes from
'TDC' to 'BDC' compare in a Wankel versus a reciprocating engine?
Somebody to forward here a chart about this? Is there a safe way,
safe for the lubricating oil film, the bearings, and the shaft, for
increasing the housing and/or Rotor working surface temperatures, a
condition that was shown improving fuel economy and cleanliness of
exhaust gases? Some tested an Iron housing, with improved results
in SFC and exhaust gases over Aluminum, but I've read nothing about
differences in thermal dilatation between housing and rotor when
both are made of iron, and if this makes possible having the engine
seized when overheated. Thanks have a nice season. Best regards.
Salut † Jose Gros-Aymerich Madrid, Spain
PS: the Napier was a Single Sleeve-Valve. 2-Stroke, compression
ignition engine, Harry Ricardo solved the problems met during
development of top power S S-V engines by making the Sleeve Open,
something like an annular piston, 10% of the piston surface, that
contributed with 3% of the total engine output via the
Sleeve-Valve operating mechanism and the crankshaft, this also
eliminated the very complex 'Junk head', of former S S-V engines.
The clean air acts had an influence on the SFC of car engines, as a
clean exhaust required a bit of fuel consumption increase, but I
was told about an experience around 1975 with a Seat/Fiat 4
cylinder, OHV, camshaft in the block side, 1438 cc car engine
being measured an SFC of 178 gr/HP/hr, pretty good.
Mazda research found that the flame propagation was not reaching the
sides of the combustion chamber when the rotor width was over 75mm.
Curtis Wright and then Ingersol Rand on the very large industrial RCE
ran into flame propagation issues and had to keep the engine RPM
low; similar to large recip industrial engines. From automotive use
limiting the RPM is not viable, so in working on the 16X development
they reduced the rotor width to 70mm like the 12A. Then to get the
displacement up they increased the eccentricity and radius. This
equates to boring and stroking a recip. According to things I read
the surface to volume ratio is improved. Better burn and increased
torque. I can see Al end housings with the exhaust going out that way
being difficult to control expansion and the wear surface integity.
The rotaries have in the past been able to meet coming emission
standards before other auto manufacturers could get their heads
wrapped around the problem. When little Mazda with the relatively new
rotary engines they had to suck their belies in and decide to get a
solution developed. If Mazda could develop a new engine and meet
emission standards they did not really have a leg to stand on. In
1974 I got lean jets from Racing Beat for my RX3. I had taken the
thermal perverter off and replaced the exhaust with a header I made
myself. To make the thermal reactor work they ran the engines rich
and injected air to burn in the perverter for cleaning the emissions.
The exhaust measured OK for the day but mileage sucked. Most of the
other cars all suffered the same problem. A 1973 Chev 1/2 ton with a
350 got worse fuel economy than one with a 454. The one with the 454
was not classed light duty but medium duty and thus did not have to
meet the stricter emissions standards. With my stock RX3 I was
getting 18 city and 21 hiway MPG IMP. After the exhaust and changing
to the lean jets for racing I was up to 27 -28 MPG on the hi-way with
the 4 spd trans. Pintos and Vegas were not any better than that. Iron
will not absorb the heat as much as Al but weight becomes an issue.
TiAl rotors would reduce the rotor weight to about 6lbs from 10lbs.
Now if you built rotors narrower and larger radius, TiAl side
housings with a detonation gun Cermet coating applied, 3 plugs per
rotor and Paul's ignition with power recovery I think we might have a
very potent power package.
Dale Davies
The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
http://www.rotaryeng.net You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.