Subject: Single Rotor balance:FAO paul Lamar
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 4/22/2015, 11:26 AM
To: AA-1-Me



   Centrifugal force of a rotating object is MVVR.  Where V is the
   velocity, and R the radius and M is mass.

   This means that unless C.G. is matched exactly, it is impossible to
   ballance the engine at different speed.

   Fortunately, I think the C.G. Of the rotor travels in a circle.
   Therefore it is van be balanced by a weight at the C.G. path of the
   rotor. The same goes for the imbalance of the eshaft.

   Since counter weight is located only at the end of the engine, I
   think you will get from limited twisting on the shaft.

   That's IMHO. No guarantee on accuracy.

   Henry Nee 於 2015/4/17 下午11:20,"paul" <rotaryeng@earthlink.net <mailto:rotaryeng@earthlink.net> 寫道:


   Hi,

   Can you please explain the problem and solution of balancing when
   using  a cut down e-shaft  with single rotor 1/2 Mazda 13b engine.

   Regards Zahid


   Balance is controlled by these equations. The Wankel is not just
   statically balanced but dynamically balanced as well.

   In a single rotor engine the counterbalance weights must provide a
   STATIC balance for the e-shaft eccentric and its rotor and must also
   account for the DYNAMIC wobble caused because the static counter
   weights are not located at the mechanical centres of the rotor and
   the eccentric. It is impossible to do this.

   They must be mathematically sized relative to their lateral position
   from the rotor and eccentric centre line.

   Paul Lamar


   the Tracy ISO is physically attached to the flywheel. Does that need
   to be brought in to balance equation  as extra mass to mF (front
   counter weight) or mR (mass Rear Counterweight)?

   Regards Zahid

   The rear counter weight is hiding behind the ISO.

   Paul Lamar

   Here is how I solved some of the balancing issues. There are a whole
   lot of issues interacting when building a new engine configuration.
   Weight control influences almost everything. A single rotor engine
   certainly requires a considerable flywheel, if one wants the idle
   speed somewhere below 3000 RPM. I integrated the rear balance weight
   in the flywheel (picture). The front balance weight I modified with
   tungsten inserts before dynamic balancing. I ended up with a clean
   rotating setup. My engine is based on 12A rotor and housing, so I do
   not have any direct comparison to 13B size parts. FWIW.


   Richard Sohn N2071U

   http://www.fairpoint.net/~res12/home.html


   Hi Richard, I have read some postings where some have machined a
   single rotor eccentric shaft from a 2 rotor unit. Paul mentions the
   shaft needs to be hardened after machining. Could you give a overview
   of the process you used to build your shaft ?

   Thanks, Steve Carlisle

   Here is what I did.

   On the first e-shaft I concerted, I left the oil pump side of the
   shaft with the front lobe unchanged. After machining the rear end of
   the shaft to my mods, I only had one bearing surface to create. I
   picked an inner ring of a INA needle bearing with an outer diameter
   the same as the original MAZDA bearing, and pressed it on the shaft.
   As it turned out, it was a solution, which never failed during all
   the ground testing of the first engine I build, with a run time of
   around 50hrs. I did not consider this a solution for a final, flyable
   configuration. The solution I have in the engine now is a case
   hardened bearing section. The biggest problem was finding someone for
   the case hardening and grinding who was willing to do it for and
   affordable cost. FWIW


   Richard Sohn N2071U

   http://www.fairpoint.net/~res12/home.html


   I misunderstood the last email by Richard Sohn. He was referring to
   case hardening process for e shaft . I thought he was referring to
   case hardening for bearing. So please do not publish my last email.

   Zahid Rahman



   I am thinking, since the rotor rotates at one third the speed of the
   esfaft. One needs a 3:1 reduction gear on the counter weight to
   matched the rotor's rotation speed.

   Corrections welcome!

   Henry Nee


           I'm not sure at all, but you have to compensate for the weight that
         is centered in the shaft eccentric, and this rotates at shaft
   speed. Or not?
          Thanks. Best regards. Salut †
                 Jose Gros-Aymerich
          Madrid, Spain


Yes, I believe you need two counter weights. One rotates at reduced speed to
balance the rotor, and a second one in same speed with the eshaft.

That's why two rotors is much better balanced.

Henry  Nee


   The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
   http://www.rotaryeng.net You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2015 All world wide rights reserved.