Subject: : GEARBOX ALMOST READY FOR ASSEMBLY
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 4/30/2015, 11:18 AM
To: AA-1-Me




    Paul and Georges Almost done before assembly. I do have the end
    shaft to be treaded 22mmX 1.5 for the safety nut and groove one one
    side to lock it . Then treated and annealed both shaft at Rockwell
    60. I will try to go at Sun&Fun this Saturday and comeback Sunday.
    Few photos for your interest. JEAN PRUDHOMME Looking real Jean. What
    does it weigh so far? I won't be at Sun & Fun this year. Too much
    patent work. Filing world wide. Paul Lamar Jean I am Pascal from
    France searching for a PSRU. Question: where did you find the bell
    housing which seems to be die casting made? And where did you get all
    these parts? Would be very interested to purchase a full set as you
    show in your photos. Since Tracy Crook retired, I really don’t where
    to find a planetary psru. If you can help, that would be great. I'm
    looking for 2.71 - 2.85 ratio.

      Thanks Best regards

    Pascal

    Jean

    No Help? Is it a secret where you got your parts?

    Regards Pascal

    The bell housing is stock Mazda. The casting on the front is a sprint
    car quick change rear end.

    Paul Lamar


    Thank you Paul I'll try to figure out on which trade mark car it is
    used and try to locate in Europe. Pascal


    I don't think they have sprint car racing in Europe. There is a whole
    industry here in the US dedicated to small oval tack racing on dirt
    and pavement. The power is up to 800 HP and the weight is 1300 pounds
    or less. There are literately 100's of small oval race tracks around
    the US.

    It is a reflection of our disposable income as is private aviation
    :-)

    Also so called live rear axles are not common in cars in Europe.
    They are disappearing in the US as well and being replaced by front
    drive independent suspension.

    Paul Lamar




    Paul Could send me your casting dimension I am working also with
    needle bearing but I can use the same housing and I am wondering if
    yours can be use. The needle bearing I intend to use is the B-3612
    eBAY Torrington they are at $19.40 EACH


    JEAN PRUDHOMME


    We don't have a casting. I suggest making the housing out of thick
    wall aluminium tubing.

    Read over this stuff. I suggest cutting the splines for the 2.85:1
    planet carrier on the end of this McMaster shaft. It is hard so you
    may have to send it out ans have it normalized. After you cut the
    splines turn it down to 2.26 OD. Then have it hardened and ground to
    2.500". See the attached timken engineering stuff. Same goes for Koyo
    bearings

    You can then use the EBAY bearings directly on the shaft. For the
    prop flange end use two 3/8 pins 90 degrees to each other like Ross
    did or use the extended point set screw trick. I suggest making a
    static  test rig for the extended point set screws and apply a 1000
    foot pounds of torque. You can use your prop flange as one part and a
    short length of tubing for the other part.

    Paul Lamar


    Paul,


    Don’t mean to be a pest, but could we just as easily use “caged version”
    of your drawn cup needle bearings, because Timken says this version
    “provides high speed and maximum lubricant retention capability.” ??
    Gene Kahn



    Unnecessary. No load on a planetary. 2800 RPM is not high speed.

    Paul Lamar


Good question. Which brand of quick change. Which size and is it a live axle or tube side cover.
The part number would be icing on the cake. My idea from years ago was to use a mini side bell
from Speedway Engineering. A short piece of axle tube with a stub tube (short hollow spindle)
and a safety hub for the prop flange. All  parts tested to death. All use massive bearings and seals
that can be had the world over, and anyone can buy over the phone. They will make an axle any
length you want, with any spline you want.
One of the reduction units at Sun&Fun used two sets of
full size high nickel quick change gears.

Lynn E. Hanover


For a given gear width a planetary is six times stronger. That is because the line contact compressive
load  between the gear is all important. The other major problem with spir gears is center to center
distance increases with temperature. This does not happen in a planetary,

Here is some sprint car stuff.

Paul Lamar



    The Rotary Engine News Letter. Powered by Linux. ACRE NL web site.
    http:www.rotaryeng.net You Tube http:tinyurl.combeqqxas Copyright
    1998-2015 All world wide rights reserved.