Subject: AN hose refresh with pics 3
From: paul
Date: 5/24/2015, 6:41 PM
To: AAA-rotaryengine


Opss forgot the pics.

I needed some dash 4 AN flex hose for the drain back out of Tracy's
PSRU all the way back to Mike Wills custom oil pan.

He had used rigid aluminium line which is a bad idea if is is really
long. In that case is tends to vibrate, fatigue and crack. On our
eight quart oil pans we have thick materiel on the front end to
accommodate a pipe fittings. There was not enough height on Mike's
trick pan to accommodated the necessary materiel and  a pipe fitting
for the PSRU drain back.

I used AN dash 4 SS braid instead.

I had to re-educated myself on adding AN reusable fittings to AN
hose. A very tricky thing to do.

These are the best written instructions I have found so far. Follow
these  instructions exactly. No skips and no short cuts. Use paper
masking tape. Duct tape and electrical tape tends to melt. Paper
tape burns and remains stiff very important.

The best thing to use for cutting the hose is a hand held friction
saw.

When tightening the back nut clamp the hose in a vice just behind
the back nut. Apply back pressure to the front nut to keep the SS
braid in the fitting.

Paul Lamar


Hi Paul,

Tracy recommends -6 ID at a minimum and notes that there should be
no are dips in the line where oil will pool and cause a small amount
of back pressure. (similar to a turbo oil return in that sense. That
will cause the oil level in the psru to rise and oil will seep out
past the input shaft seal.

SS braid is also overkill on a line that sees no pressure,
particularly over on the cold side of the engine, but I recommend at
least -6.  I have always gotten a misting of oil coming out past
that seal because it is difficult to achieve Tracy's goals.  I think
that is why Mike used rigid lines, very light weight and easier to
prevent dips.  With no pressure in the line a typical crack is
unlikely to be catastrophic.

Food for thought.

Glad to see you putting some time into it.

Dave Leonard


Thanks Dave, for paying attention and checking my work.

I needed an engine to test the LII MS ignition as it is a BIG deal
:-) Patent applied for in 100 countries.

I'll risk it and use a better seal on the input shaft. Tracy used a
too cheap seal :-).

Here is the hot tip shaft seal for this important location. SS spring
loaded Teflon.

How many hours do you have now Dave on your Mazda Turbo powered RV6
?


Paul Lamar


Thanks for the tip on the input shaft seal.  I will put one in next
time I take apart the gear box for inspection, probably when I reach
1000 hrs barring any other incident.  I think I have about 850 or so
now. Not much flying in the last couple of years.

Great to hear about the ignition.

Dave Leonard

Most people only put 50 to 100 hours a year on their private
aircraft. 850 hours is a lot.

BTW I will let everybody know when there is something to see on the
turbo 650 HP 2 rotor time to climb Harmon Rockets [RV4] and you can
fly in to SZP for lunch. The restaurant is now open again.

The crew don't work on it during weekends and Dan closes the
shop/Hangar when he is in in Sydney or London on a flight so it will
be a moments notice basis. Dan also goes home eevery day about 4 PM.

Paul Lamar

Paul,

  Do you have a part # and/or supplier for that "Teflon " input shaft seal
for the RDX redrives ??..............


Kelly Troyer


I thought sure I sent this attachment out twice. Did you not get this?

The first time I sent it out was 05/19/2015 04:51 PM PST.
I received a copy on my computer. Check your email inbox and
see if you got it.

The subject box was "AN hose refresh with pics"

If you get this message send me email with one word. "OK"
I think the NSA is losing some of my email.

Paul Lamar


The Rotary Engine News Letter. Powered by Linux.
ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Store http://www.rotarpower.com/#!
Copyright 1998-2015
All world wide rights reserved.