Subject: Welding the cross counter flow rads.
From: paul lamar
Date: 7/19/2015, 2:19 AM
To: A10-Me-Earthlink



   Cross counter flow is a more effective heat exchanger.

   Here is the sequence for welding the rads to make a cross counter
   flow heat exchangers.

   Butt tig weld the in and out tanks first by cutting off all tabs on
   the rads.

   Don't weld the in and out tubes on yet.

   They will be marked for position on the tanks while on the aircraft.

   Then the large holes for the tubes will be cut and then the tubes
   will be welded over the holes. The tank design will vary depending on
   cool side mounting or bottom mounting. The TTC is a bottom mount.
   Most other aircraft use a cool side mount. The 3 rotor allows longer
   rads to be used. Put the diffuser between the rads and the engine.
   See my book How to Cool your Wankel for more info.

   After the tanks are done (with out the holes and tubes) bolt the
   rads together with the wood strips leaving 1/2 to 3/8 of an inch
   between in and out tanks.

   The idea here they must not touch each other. The wood strips are
   heat insulators between the two rads.

   Then weld an aluminium strip 1/2" to 3/8" wide at the other end.
   Finish by boxing in the other end (the front end).

   Weld on them some and let the rads cool some what. They are brazed
   together at only 1100 F so it is important to not get them too hot.
   Wet rags around the ends of the fins and tubes might help.

   Here are a bunch of pictures attached. The JPGs were Dodge Neon rads
   and not the truck rads. The TTC rads will be welded soon.

   Apparently when Mercedes owned Chrysler they implemented some up to
   date heat exchanger technology. IMHO Chrysler rads are now the best
   from an efficiency point of view I have found so far. Honda also uses
   up to date tech but they are more expensive.


   Paul Lamar



   What about a dual pass rad already done?
   http://www.jegs.com/i/Allstar-Performance/049/ALL30048/10002/-1

   -Matt Boiteau


   It will probably work but you will be paying a weight and drag penalty.
   I don't know how much on the drag penalty. We don't have any comparison data
   on the drag yet. The weight of the core with water will be at least
   150% of the cross counter flow Dodge truck rads.

   Paul Lamar

   For maximum efficiency, you don't want to use the flow pattern described in
     their (Allstar's) text, use the pattern from Paul's book. The top core
   (or first core
   exposed to cooling air) is the second core the coolant flows through.

   This better utilizes the Delta/T thermal transfer to the cooling air
   flow. Read Paul's
   book for counter cross flow cooling theory.

   C. Smith

   Craig, can you send me that Allstar text. I found their web site but I
   can't find anything
   about that. Apparently they use two rows of one inch tubes . The Dodge
   truck rad is one
   row of .7 inch tubes.

   http://www.allstarperformance.com/instructions.htm

   In theory one could cut the AllStar rad apart into a top and bottom for
   a cross counter flow
   reconfiguration. That would give more core volume if two Dodge truck
   cores were
   not enough core volume . Slightly less efficient however.


   The basic idea is you want as large a frontal area you can fit in the
   cowling with core
   volume of about 500  inches. The Dodge truck core are about  465 cubic
   inches and will probably work with 250 HP. We now have about 930 cubic
   inches
   in the time to climb rad which I am guessing will be good for about 500 HP.

   I suspect the time to climb cross counter flow rad is not enough core
   volume for 650 HP and
   we will have to spray cold water on the assembly.

   We used think we needed 650 cubic inches for 250 HP and that was before
   we discovered
   the the much improved Kays & London wedge diffuser.

   Ian in Perth Oz did some experimenting  with a Kays & London  S shape
   diffuser lying
   on it side and was able to reduce the size of the air intake to 10 to 15%
   of the core frontal area. That, in theory, reduces the cooling drag.
   Ian  routinely flies
   around the outback.

   Ian has  built two RV6's powered by rotaries. The first one crashed when
   a hose blew off a rad with out a bead on one of the tubing ports.


   Paul Lamar

   Allstar Performance dual pass radiators circulate coolant across the top half of the radiator, then back across the bottom half, allowing up to twice the heat dissipation. These radiators offer furnace brazed tanks, two rows of 1" tubes, billet machined filler necks with overflow, standard 1-3/4" outlet and feature a universal inlet design to accept 1-1/2" standard hose, -16 or -20AN fittings (sold separately).


   Triple Pass Radiators:
   Allstar Performance triple pass radiators circulate coolant across the top portion of the radiator, back across the mid-section and through the bottom allowing maximum heat dissipation. These radiators include furnace brazed tanks, two rows of 1" tubes, billet machined filler necks with overflow, standard 1-3/4" outlet and a universal inlet designed to accept 1-1/2" standard hose, -16 or -20AN fittings (sold separately .

     """""

   C.Smith

   As Craig points out much of this is misleading or incorrect.
   The lower half of a two pass is less efficient  as the temperature
   of the coolant is lower by that time. The trick is the keep
   the temperature DIFFERENCE as high as possible through out
   the heat exchanger.

   However we accept this for the convenience of having the inlet and out
   let on the same end and with the lower cost of a non counter cross flow
   configuration.

   Paul Lamar


The illustrated radiator is either a conventional single pass
or a three pass radiator. A dual pass would have both hose
connections on the same side of the radiator. The tank has
a baffle across it to block the coolant flow so it takes the
designed path through the core. Not much advantage over
a conventional radiator. The cross counterflow design has
the hot coolant from the engine cooled by the warm air that
has already passed through the cooler side core. The coolest
air from outside cools the cooler coolant just before it goes
back to the water pump. This will provide the highest temperature
differential across the radiator.

Dale Davies



   The Rotary Engine News Letter. Powered by Linux.
   If you want off the list PLEASE let me know and I will
   remove  you.  ACRE NL web site. http://www.rotaryeng.net
   You Tube http://tinyurl.com/beqqxas
   Copyright 1998-2015 All world wide rights reserved.