Subject: If the helicopter industry does not adopt this engine they have no brains.
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 8/8/2015, 6:13 PM
To: A10-me-earthlink


I am sure that Felix Wankel and all other early adopters including
Mazda would have had  no idea that 650 HP would be extracted
out of a 200 pound, two rotor, Mazda engine.

One thing has become crystal clear. Spark plug cooling is a major issue
in high HP Wankel's. Jim Mederer has done wonders in addressing
this issue.  However the time has come to rethink the cooling system
to make it better.

This is the way I would do it. Put the cold water in the centre housing
near the spark plugs. Let it flow fore and aft and come out of the centre
housing on the other side.

The center housing has another job and that is scavenging the hot
cooling oil out of both rotors.

The easiest way to do that is run the engine plugs up and rearrange
the oil drain backs. For an aircraft that makes a lot of sense. That way
the hot water, hot oil and the exhaust comes out the bottom of the
centre housing.

The turbo can also be under the engine. Fuselages are higher than they are
wide because sitting people are higher than they are wide.

This concept not done yet. I have a lot more work to do when I find some
spare
time from the ignition biz.

Thanks to Larry Childs for the excellent rotor housing 3D's.

Paul Lamar


BTW a Super Cub with this engine would set world records
for STOL take off and landing.


Paul,

My plan for putting a turbocharged two rotor in a Rotorway Exec uses a 90 degree primary reduction and eliminates the primary reduction that is stock on the Rotorway.  I think the same configuration would work in a Bell 47 because you could have a 2 to 1 reduction going into the Bell's gearbox and allow the engine to be horizontal with 3000 rpm going into the helicopter transmission.  On the Rotorway, it allows me to get rid of a first stage transmission, saving a bunch of weight.


The engine would run at around 6000 rpm continually with torque being controlled with the throttle so it would act like a turbine engine.  I would love to have a Bell 47 G2 but it is a certified helo with all the baggage that that comes with.  Rotorway Execs with blown engines are readily available and they are said to fly better than Robinson R22s.


The Rotorway's main rotor is designed for 150 hp, the tail rotor and accessories take another 40 or so more.  So, a turbocharged two rotor would be flat-rated, operating at around 65% power at sea level and I would have 200 hp available at 10,000 feet.  On top of that, I would have another 100 lb. useful load and the Rotorway is already designed for a liquid cooled engine.
This is a picture of BJ Schramm's Windstar:
http://files.activeboard.com/tn-1322570?AWSAccessKeyId=1XXJBWHKN0QBQS6TGPG2&Expires=1440028800&Signature=GEgGuoIPNqIFGcfwKkPnMGKv9MU%3D
It had a custom built, 350 hp, 6 cylinder engine and would have been successful with a turbocharged three rotor.  Such a shame, it would have been a great helicopter!

Steve Brazil

If you could redesign the rotor system for 650 HP you could set a world
altitude record for helicopters. Gas turbines don't work that well at high
altitude.

Another way is limit the boost at low altitudes and just use full boost up
high.

With the turbo we have there is a bleed port in the exhaust manifold to limit
the boost. In other words we are not using all the boost available
and we are still getting 650 HP.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.