Subject: If the helicopter industry does not adopt this engine they have no brains. 10
From: paul lamar
Date: 8/9/2015, 7:39 PM
To: A10-Me-Earthlink



I am sure that Felix Wankel and all other early adopters including Mazda would have had no idea that 650 HP would be extracted out of a
200 pound, two rotor, Mazda engine.

One thing has become crystal clear. Spark plug cooling is a major issue in high HP Wankel's. Jim Mederer has done wonders in addressing this issue. However the time has come to rethink the cooling system to make it better.

This is the way I would do it. Put the cold water in the centre housing near the spark plugs. Let it flow fore and aft and come out of the centre housing on the other side.

The center housing has another job and that is scavenging the hot cooling oil out of both rotors.

The easiest way to do that is run the engine plugs up and rearrange the oil drain backs. For an aircraft that makes a lot of sense. That way the hot water, hot oil and the exhaust comes out the bottom of the centre housing.

The turbo can also be under the engine. Fuselages are higher than they are wide because sitting people are higher than they are wide.

This concept not done yet. I have a lot more work to do when I find some spare time from the ignition biz.

Thanks to Larry Childs for the excellent rotor housing 3D's.

Paul Lamar


BTW a Super Cub with this engine would set world records for STOL take off and landing.




Paul, I was reading an article a little while ago, about putting quantum particles (silver or gold or copper or something) into the water and vastly improving the thermodynamic efficiency of it (the water). Something in the region of 50% if I recall correctly, it could be your answer to your cooling problems. If you think the idea has merit I'll try and find the article, I think it was in New Scientist mag. Chris. Hoskins

I would be very interested in that.


Paul Lamar


This is not a surprise as any material with high thermal capacity would help to improve cooling. The problem is to keep the particles suspended over long periods of time, and at different temperatures.


Gordon

I am worried it would plug up the heat exchanger.

On the micro level... how well does the water transfer the heat to the particles?

Paul Lamar

At the nano meter size, the particle receives and gives out heat instantaneously. So in theory this works. The trick is to have stable suspension, perhaps by using surfactants to make the particle surface pro water. Thus the particle would suspend in the water like emissions similar to milk. But surfactants mostly are not stable at high temperature. So after some time the metal particles would settle to the bottom.


Gordon

A few years ago, Detroit Diesel became aware of a coolant problem.
There are three compounds whose nomenclature seem similar. Silcone, Silica, and Silicate (Sodium Silicate). Silicate is used as a corrosion inhibitor. Detroit Diesel found that over time the silicate would come out of suspension and form a sand like substance in the cooling system. While the engine was running this stuff would be picked up in the flow and due to it's gritty nature take out the water pump seal. How would these tiny bits of metal work in the cooling system?

Dale Davies


    Also, be aware that there's considerable health concern over nano-particles.  In a nutshell, the blocking/filtering mechanisms we have in our body (skin, cilia, mucous membranes, etc) aren't built to keep particles of this size out--they are rarely found in nature, so there's not much need for a defense against them.  But when deliberately made and introduced, they can get in and then concentrate in various tissues.  Also, the characteristics of some substances change at nano-scales, and so just because a substance is innocuous at normal particle sizes does not mean they are not a problem as nano-particles.
    Nanoparticles were being put into all kinds of consumer products as the next "new thing", now manufacturers are turning 180 degrees and removing the substances in light of these concerns.
    More in this paper: http://www.ncbi.nlm.nih.gov/pmc/articles/PMC544578

Mark Waldron



Hi Paul,
   I have found the article on adding nano particles to water, it is in New Scientist magazine 6th July 2013, a report on Fluid thinking. A good read !
   Chris.

The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.