I am sure that Felix Wankel and all other early adopters including
Mazda would have had no idea that 650 HP would be extracted out of a
200 pound, two rotor, Mazda engine.
One thing has become crystal clear. Spark plug cooling is a major
issue in high HP Wankel's. Jim Mederer has done wonders in
addressing this issue. However the time has come to rethink the
cooling system to make it better.
This is the way I would do it. Put the cold water in the centre
housing near the spark plugs. Let it flow fore and aft and come out
of the centre housing on the other side.
The center housing has another job and that is scavenging the hot
cooling oil out of both rotors.
The easiest way to do that is run the engine plugs up and rearrange
the oil drain backs. For an aircraft that makes a lot of sense. That
way the hot water, hot oil and the exhaust comes out the bottom of
the centre housing.
The turbo can also be under the engine. Fuselages are higher than
they are wide because sitting people are higher than they are wide.
This concept not done yet. I have a lot more work to do when I find
some spare time from the ignition biz.
Thanks to Larry Childs for the excellent rotor housing 3D's.
Paul Lamar
BTW a Super Cub with this engine would set world records for STOL
take off and landing.
Paul,
My plan for putting a turbocharged two rotor in a Rotorway Exec uses
a 90 degree primary reduction and eliminates the primary reduction
that is stock on the Rotorway. I think the same configuration would
work in a Bell 47 because you could have a 2 to 1 reduction going
into the Bell's gearbox and allow the engine to be horizontal with
3000 rpm going into the helicopter transmission. On the Rotorway, it
allows me to get rid of a first stage transmission, saving a bunch of
weight.
The engine would run at around 6000 rpm continually with torque being
controlled with the throttle so it would act like a turbine engine.
I would love to have a Bell 47 G2 but it is a certified helo with all
the baggage that that comes with. Rotorway Execs with blown engines
are readily available and they are said to fly better than Robinson
R22s.
The Rotorway's main rotor is designed for 150 hp, the tail rotor and
accessories take another 40 or so more. So, a turbocharged two
rotor would be flat-rated, operating at around 65% power at sea level
and I would have 200 hp available at 10,000 feet. On top of that, I
would have another 100 lb. useful load and the Rotorway is already
designed for a liquid cooled engine. This is a picture of BJ
Schramm's Windstar:
http://files.activeboard.com/tn-1322570?AWSAccessKeyId=1XXJBWHKN0QBQS6TGPG2&Expires=1440028800&Signature=GEgGuoIPNqIFGcfwKkPnMGKv9MU%3D
It had a custom built, 350 hp, 6 cylinder engine and would have been
successful with a turbocharged three rotor. Such a shame, it would
have been a great helicopter!
Steve Brazil
If you could redesign the rotor system for 650 HP you could set a
world altitude record for helicopters. Gas turbines don't work that
well at high altitude.
Another way is limit the boost at low altitudes and just use full boost up
high.
With the turbo we have there is a bleed port in the exhaust manifold to
limit
the boost. In other words we are not using all the boost available
and we are still getting 650 HP.
Paul Lamar
That would certainly make people pay attention. 42,500 feet is pretty high.
David Josephson
Actually, you would not get that high. Helicopter rotor blades are
designed
to run at close to max L/D so their horsepower isn't wasted. At a given
weight and altitude, the blades will stall regardless of the horsepower
available.
Steve Brazil
Would specifically designed for high altitude blades work?
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove you. ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.