I am sure that Felix Wankel and all other early adopters including
Mazda would have had no idea that 650 HP would be extracted out of
a 200 pound, two rotor, Mazda engine.
One thing has become crystal clear. Spark plug cooling is a major
issue in high HP Wankel's. Jim Mederer has done wonders in
addressing
this issue. However the time has come to rethink the cooling system
to make it better.
This is the way I would do it. Put the cold water in the centre
housing near the spark plugs. Let it flow fore and aft and come out
of the centre housing on the other side.
The center housing has another job and that is scavenging the hot
cooling oil out of both rotors.
The easiest way to do that is run the engine plugs up and rearrange
the oil drain backs. For an aircraft that makes a lot of sense. That
way the hot water, hot oil and the exhaust comes out the bottom of
the centre housing.
The turbo can also be under the engine. Fuselages are higher than
they are wide because sitting people are higher than they are wide.
This concept not done yet. I have a lot more work to do when I find
some spare time from the ignition biz.
Thanks to Larry Childs for the excellent rotor housing 3D's.
Paul Lamar
BTW a Super Cub with this engine would set world records for STOL
take off and landing.
Paul,
My plan for putting a turbocharged two rotor in a Rotorway Exec uses
a 90 degree primary reduction and eliminates the primary reduction
that is stock on the Rotorway. I think the same configuration would
work in a Bell 47 because you could have a 2 to 1 reduction going
into the Bell's gearbox and allow the engine to be horizontal with
3000 rpm going into the helicopter transmission. On the Rotorway,
it allows me to get rid of a first stage transmission, saving a
bunch
of weight.
The engine would run at around 6000 rpm continually with torque
being controlled with the throttle so it would act like a turbine
engine. I would love to have a Bell 47 G2 but it is a certified helo
with all the baggage that that comes with. Rotorway Execs with
blown
engines are readily available and they are said to fly better than
Robinson R22s.
The Rotorway's main rotor is designed for 150 hp, the tail rotor and
accessories take another 40 or so more. So, a turbocharged two
rotor
would be flat-rated, operating at around 65% power at sea level and
I
would have 200 hp available at 10,000 feet. On top of that, I would
have another 100 lb. useful load and the Rotorway is already
designed
for a liquid cooled engine. This is a picture of BJ Schramm's
Windstar:
http://files.activeboard.com/tn-1322570?AWSAccessKeyId=1XXJBWHKN0QBQS6TGPG2&Expires=1440028800&Signature=GEgGuoIPNqIFGcfwKkPnMGKv9MU%3D
It had a custom built, 350 hp, 6 cylinder engine and would have been
successful with a turbocharged three rotor. Such a shame, it would
have been a great helicopter!
Steve Brazil
If you could redesign the rotor system for 650 HP you could set a
world altitude record for helicopters. Gas turbines don't work that
well at high altitude.
Another way is limit the boost at low altitudes and just use full
boost up high.
With the turbo we have there is a bleed port in the exhaust manifold
to limit the boost. In other words we are not using all the boost
available and we are still getting 650 HP.
Paul Lamar
That would certainly make people pay attention. 42,500 feet is
pretty
high.
David Josephson
Actually, you would not get that high. Helicopter rotor blades are
designed to run at close to max L/D so their horsepower isn't
wasted.
At a given weight and altitude, the blades will stall regardless of
the horsepower available.
Steve Brazil
Would specifically designed for high altitude blades work?
Paul Lamar
Perhaps you folks would want to research before offering hunch as
fact.
The world's altitude record for helicopters *is* 42,500 feet, set in
2002 by Fred North in an Aerospatiale AS350B. For 30 years the
record
stood at 40,814 feet set in 1972 by Jean Boulet (followed by the
record
which still stands for the longest autorotation, because the engine
flamed out at the top, still climbing) in an Aerospatiale AS315B
Lama. I
have many hours as copilot/operator in Lamas which we used for
geophysical survey. Lama blades *are* specifically designed for high
altitude work, as is the whole helicopter. They also work just fine
at
sea level.
Do you think a three-rotor turbo Mazda engine would maintain climb
power
at FL 420?
David Josephson
I don't know. I do know there is about 20% more energy in the rotary
exhaust
compared to four cycle piston engines to pump them up.
Evidence is the fact that CW found the exhaust valve dissipated
20% of the
exhaust energy. As far as more evidence is concerned many rotaries
have been
pumped up to extraordinary high HP levels for the displacement. Our
time to
climb engine is a good example.
We are not using an inter cooler which in theory would be required
for high altitude to keep
the intake temperature down at high pressure ratios. Obviously Jim
Mederer is
not worried about detonation. The P38 was limited to 145 degree F
intake
temperature.
Another fact is; turbo chargers work better at altitude because the
back pressure
is reduced and the turbo speeds up. MacInnis says 2% per thousand
feet but
there are many other factors like intake air temperature to deal
with.
MacInnes wrote the bible called "Turbochargers" HP Books.
A P47 and P38 got up to 43,000 feet in WW II so a turbo rotary
engine should do
better in theory.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove you. ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.