Subject: 13b running at half power
From: "rotaryeng@earthlink.net" <rotaryeng@earthlink.net>
Date: 8/29/2015, 11:57 AM
To: A10-me-earthlink

it
does anyone have a 13b with a micro tech ignition sys i have one and i have tried just about everything i can think of but iam still only getting 5000 rpm and only if i advance the timing if i take the prop off  of course it will wind up to 9000 in a hurry the spark is good to both rotors ive moved the timing in both directions only to vary the rpm from 3000 to 5000 my a/f ratio i s from 12 to 13.5 down around 10 at idle i am not sure if its the computer or the engine any ideas

bob obrian

What is the gear box ratio?

What is the prop diameter?

what kind of porting?

Paul Lamar


Rd 1c 2.85:1

74 dia 88 pitch

standard 6 port was it so close i couldn't see it

thanks

bob OBrian

Mostly the prop is too large. Cut it down to 68" in dia. A p-port would gain 50 HP at least depending on what your 6 port manifold looks like. Send me a picture. I can then estimate the power.

Paul Lamar

I'm having the same problem with my naturally aspirated six port RX8 rotary in my Bush Caddy aircraft, max RPM is only 6100.  I'm using a three blade 76" magnum Ivo prop.  I removed one blade and tried it with the two blade set-up, problem even got worse, down to 5600 RPM.
Doesn't make sense to me.  Another thought I have is an exhaust restriction. I'm using a racing SPINTECH 2 1//2" inlet & outlet muffler. Anyone have any thoughts on this?

Thanks, Bob Forbes

What is your gear box ratio Bob?

It is not the number of blades. The diameter is too large. The tips of the prop are running into the transonic brick wall. Cut it down to 68" and sand the  tip to a thin air foil section.

Here is the best muffler to use. Sounds better as well. Works somewhat like a ramjet.

That SPINTECH will destroy it self. Inspect it internally  with a Harbor Freight digital inspection camera after every flight. Aircraft have crashed when an automotive muffler was used and plugged up. VERY IMPORTANT!

The coax muffler is much easier to inspect.

The intake manifold is critical.  Here are some old pictures of your manifold. We had this discussion in the past and I am sure I recommended longer intake runners. There should be plenty of room in a Bush Caddy for longer runners. 18 to 20 inches is about right.


Paul Lamar


Thanks for your resourceful response Paul.  I'm using Tracy's 2.85:1 PSRU.  I will cut the prop down and try that when I get time.  Yes, we have had this discussion pertaining to my intake manifold in the past.  I know my intake would be much better with longer runners, I'm just reluctant to spend the time re-doing my intake system. If I can get 200 HP with the way it is I won't need to worry about, if not I'll have no choice but to change it.  My Bush Caddy requires 180 -
250 HP.  Today's engine run, rpm maxed out at 5800 and 114 hp.
(according to Tracy's engine monitor) Not good!

The SPINTECH muffler is completely constructed 321 SS, with a very simple welded-in baffle system.  Thanks, I will keep an eye on it with a inspection scope.

Paul, did you get your ignition system up and running, and is it on the market yet, it has to be simpler than Tracy's to set-up. There must be a simpler system then Tracy's out there somewhere.  I'm about ready to send Tracy's EC3 to the bottom of the river.  Too many adjustments and mind boggling to set up.  I have it running well at mid-high rpm's, but runs lousy at low rpm's.  If there are other folks on your news letter list having difficulties with Tracy's engine controller would they please let me know.  I'm at a lost with this one.

Thanks again, Bob Forbes

You will need the proper length to get 200 HP assuming there is a good match between the runners and the ports. 200 at 7000 is certainly doable.

What diameter are the runners? It is tricky matching round tubes to oval ports. That is a major reason I gave up on side ports as I would have had to  make the casting patterns over and over again every time Mazda changed the shape of the ports. The round hole of a p-port in a rotor housing was and is much simpler not to mention an easy 250 HP.

The static RPM should go up to about 6900 cutting down the prop to 68"
The IVO is not the best choice in the world as it is variable twist rather than variable pitch. Sanding the tips down should help a little bit.
The RPM will go up when you are in the air as the prop is stalled when running it up static  tied down. The prop usually comes out of stall around 60 MPH.

However there must be something else going on when you went to 2 blades instead of three.

My latest iteration on the ignition system is simpler.
There for a while one had to have one of my fast  low cost computers to control it.
I built in a little more circuitry in to allow the use of a simple trigger disk on the nose of the e-shaft. This takes the place of the computer for spark programming. The number of holes and their spacing can be changed to control the number of sparks and how many degrees after top dead centre they occur. It can still be triggered by a computer but there are lower demands on the software and the speed of the computer.

A super simple to program Maximite will now do the job along with EFI and EFIS.

This is what the latest packaging looks like. The trigger disk is rotated here by an DC electric motor for demo and testing purposes.

The rotary powered RV4 I am going to test the ignition on now has a 2 barrel
500 CFM Holly carb. I got rid of my Tracy stuff for the same reason you did :) Unfortunatly the gear box is 2.13 so I need a new gear box and a prop that rotates in the right direction.

Paul Lamar


Paul, You asked the diameter of my runners.  I used half of the stock intake as the attached photos show.  Notice the bevel (bell mouth) in one of the photos.  I thought this would be the easiest transition from oval to round.

Bob Forbes

Good illustration of why we went to P-ports :-) Too complicated to deal with
six ports. Intakes are aerodynamic systems and skin friction drag matters.
Six small runners have more skin friction drag than two large runners.
Mazda had no choice in the matter as they had to get torque and HP
at 3000 RPM so the car would accelerate in 6th gear on the free-way.
They should have installed an automatic manual transmission instead
and they would have wound up with more maximum HP and a less
bulky intake system.  As it is now in the RX8 the intake takes as much room
as the engine. If they were cleaver they would have copied the rotating
variable length intake runner system from Mercedes and others.

Be all that as it may one needs to deal with it or take ones engine apart
to P-port it. That would be the fastest in terms of time. The cost would
be about the same. Here is what Milo Burrows came up with to get the required
runner length. Nice job Milo.

Don't be afraid to take your RX8 engine apart. It is just a storage problem
to make sure the seals go back in the same slots they came out of.
Other than that it is 10 times easier than a piston engine.
It comes apart in a half hour. Cleaning the rotors takes the
most time but I get them bead blasted for a couple of bucks each.
Make sure you protect the rotor bearings.

There are plenty of how to do it manuals out there for free.

Paul Lamar

The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove  you.  ACRE NL web site. http://www.rotaryeng.net
You Tube http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.