I would look at the mixture at 5,900 RPM with a EGT in each header and a
heated oxygen sensor.
A heavy load at 5,900 RPM should be in the 12:1s..
The lack of change past half throttle suggests intake disruption or
blockage. and/or oversized throttle body.
The stock 6 port intake although with short runners produced plenty of
HP for the car. Another place to look is the accuracy of the TDC and
timing marks on the pulley. You have to know for a fact what is the
ignition timing. And the trailing never fires before the leading.
Painting timing marks between the flywheel teeth is more accurate and
easier to read.
A stalled propeller is easier to turn up than an unstalled propeller, so
that should not be a factor.
Lynn E. Hanover
Lynn's got some good points as usual. Bob, do you have a manifold
pressure gage?
If so what is it reading at 5900 RPM? Where is the manfold pressure tap
mounted?
One bad one :) The stalled fix pitch propeller. Every pilot knows that
from a static run up.
Paul Lamar
Paul, Yes, I have a MP gauge, using Tracy's EM2. MP tap is in the end
of my intake air plenum, you can see it in the photo I sent earlier
today (photo 036.jpg) opposite end from the throttle body. I had the MP
ports originally located in the factory oil injection ports, however was
not working properly. Tracy told me to move it to the intake manifold
plenum, made a big difference. At this time I'm hand mixing the oil and
gas. When I get this engine running properly (I hope!)I will no longer
mix by hand. I will be using the oil injection pump that I bought and
installed and not mixing oil by hand with the fuel. I know you sell MP
port fittings, however I do not wish to mix oil with the gas by hand as
I did years ago in the old snowmobiles, pain the you know what. MP @
5900 RPM is 29.8
Thanks
Bob Forbes
That could be misleading the computer. There might be a strange
dynamic pressure effect
with that huge ram pipe. The pressure is higher in the plenum than in
the runners.
That would lead to a very rich mixture. Is there any black smoke coming
out of the
exhaust? On the other hand the tapered plenum could have a strange
effect with
the pressure tap on the small end.
What about Neal's question about the size of the injectors?
You could drill and tap all the runners for a 1/16th NPT to hose barb
and Tee them all together.
A Maximite or a notebook computer and a USB data ack system would tell
you for sure.
We learned tons when we did that on a p-port engine.
One of the problems with Tracy's system you have no way of knowing what
it is
doing. The source code is secret and it keeps you in the dark. That
problem would
be solved with a Maximite as you can display all parameters on a small
VGA monitor
while it is going about its biz of controlling the EFI.
Did you try the 2 blade at 68 inch diameter?
Paul Lamar
Paul, I did try the 68" prop in the two blade configuration, but made no
change in rpm.
Thanks Neal for your input, I'll take all the help I can get. I'm using
the 4 yellow injector as per Tracy's suggestions. I believe my EC3 was
programmed at Tracy's shop for the yellow ones. I don't think the EC3
would allow me to us a larger flow injector.
There are so many variables with this set-up its mind boggling. It
could be one thing or a multitude of things.
Thanks,
Bob Forbes
You may have a Helmholtz resonator and not know it.
It could be resonating at an unfavourable frequency.
The only way to know is use a fast pressure sensor and an oscilloscope
or some sort of data acq system.
Paul Lamar
The Rotary Engine News Letter. Powered by Linux.
If you want off the list PLEASE let me know and I will
remove you. ACRE NL web site.
http://www.rotaryeng.net
You Tube
http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights reserved.