Subject: Engine RPM only 5900
From: paul lamar
Date: 11/9/2015, 7:11 AM
To: A10-Me-Earthlink



This email is to address Scott Gettings wanting to know if  anyone
else has a set-up like his Renesis 6 port.  I have the same  set-up as
Scott, and I'm using only the four yellow injectors and have the two
red ones blocked off, as per Tracy's direction.


However  Scott, I cannot get over 5900 rpm. The engine rpm does not
increase after  half throttle.  I checked to make sure the throttle
body was opening  all the way, and it is. I also removed my muffler
and replace it with a  straight pipe thinking there might be an
restriction, not the case, made no  difference in rpm.  I chopped my
three blade 76" prop down to 68" and  still no change in rpm. I'm also
using part of the original six port  intake, with no runner length.
Now the only thing I can think of is the  engine cannot get enough
air.  Looks like I have no choice but to  completely redo my intake or
try installing a super charger to force more  air in.  Not sure if
that will work or not. I'm using Tracy's EC3,  EM2, & 2.87 PSRU.

Bob Forbes


The intake configuration  and pipe length are critical for the HP.

The prop runs into a brick  wall when the tips get close to Mach One.
What is your gear box ratio?  Sounds like 2.2:1.   A 3.12:1 would work
better with the  rotary.

When the prop torque requirements meets the torque out of the  gear
box the prop  and engine of course will stop increasing in  RPM.

You can move peak torque around with intake pipe length. You  need
roughly 18 to 20 inches of intake pipe length. The longer the  pipe
length the lower the torque peak RPM.

A p-port engine will  increase the max torque at any pipe lenght.

So too will NOS :-) This is  probably the cheapest and quickest. Makes
up for a lot of intake  configuration errors :-)

A turbo charger is more economical than a  super charger as it uses
the otherwise waste energy in the exhaust to super  charge the
engine.

Paul Lamar

Bob please read this section of  the web site.

http://www.rotaryeng.net/intake.html

Paul  Lamar


Thanks for Bobs output. Questions I have include what  is  the prop
pitch and the  throttle body diameter? Is this  static or in-flight
RPM? I agree the gear ratio maybe also an  issue.

I also have built a short and compact intake system (sounds  like
yours) with possible nitrous back up for take off if necessary.   I
will test the entire engine system  mounted in an airboat prior  to
flight, which should give me some good data for this  pusher
configuration.

Thanks!

Scott Gettings.

Attached  are a few pictures of my short intake manifold. I certainly
realize this  may not result and anywhere near Optimal horsepower,
but it was simple to  build. The throttlebody is 2 7/8 inches inside
diameter.    Although shorter, it is still much less restrictive than
the stock intake  manifold system. It can also receive ram air from
the cowl intake. If this  does not produce enough power in testing, I
will convert to the  over-the-top runners configuration.

Of course, this is not an  endorsement of this solution compared to
the longer runners, as Paul has an  incredible depth of experience in
this area.

Scott  Gettings



Another possibility is that you are over driving the  prop. When this
happens the blades stall and creat drag. You, in this case  can hear
a definite change in prop noise.

If this is the case and  you are satisfied with your prop,as it is, on take
off, slowly advance the  throttle. As the craft accelerates the angle of
attack of the blades  changes and more power is able to be absorbed
as you continue to advance  the throttle.

Rich. Goldman (Been there)


I would look at the mixture at 5,900 RPM with a EGT in each header and a
heated oxygen sensor.
A heavy load at 5,900 RPM should be in the 12:1s..

The lack of  change past half throttle suggests
intake disruption or blockage. and/or oversized throttle body.


The  stock 6 port intake although with short runners produced plenty of HP for the
car. Another place to look is the accuracy of the TDC and timing marks on the
pulley. You have to know for a fact what is the ignition timing. And the
trailing never fires before the leading. Painting timing marks between the flywheel teeth is more  accurate and easier to read.

A stalled propeller is easier to turn up than an unstalled propeller, so
that should not be a factor.

Lynn E. Hanover

Lynn's got some good points as usual. Bob, do you have a manifold pressure gage?
If so what is it reading at 5900 RPM? Where is the manfold pressure tap mounted?

One bad one :) The stalled fix pitch  propeller. Every pilot knows that from
a static run up.

Paul Lamar


The Rotary Engine News Letter. Powered by Linux. If you  want off the
list PLEASE let me know and I will remove  you.   ACRE NL web site.
http://www.rotaryeng.net You Tube  http://tinyurl.com/beqqxas
Copyright 1998-2015 All world wide rights  reserved.